Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: 3t3d

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. What about members who are only dead from the...

    What about members who are only dead from the neck up?

    Otherwise, a wanted feature, a searchable page, not 100's of posts to dig through.
  2. Thread: Memorial Section

    by 3t3d
    Replies
    42
    Views
    2,036

    Hopefully there is a page to be searched, not...

    Hopefully there is a page to be searched, not just a lot of entries you would have to read the all to find if someone is gone.

    And, what about Mr. Slammy ?
  3. Replies
    14
    Views
    1,050

    Just like a car that went under water. Even...

    Just like a car that went under water. Even drying it out, it will be forever dying on the inside..

    Get rid of it, the death in the air will slowly eat at you too.
  4. You are not familiar with all the wacky liberal...

    You are not familiar with all the wacky liberal policies?
  5. Replies
    13
    Views
    724

    So, is this about an heir apparent, or no hair...

    So, is this about an heir apparent, or no hair apparent?


    Don't forget the gorilla, ... a hairy parent.
  6. Replies
    53
    Views
    3,577

    50/50 sugar, and plaster of Paris They never...

    50/50 sugar, and plaster of Paris

    They never seem to develop an immunity. So I was told.
  7. Replies
    110
    Views
    7,305

    Just found this thread, read the OP and not much...

    Just found this thread, read the OP and not much else...

    I am in the Eau Claire area and everyone is hiring!! Especially 10 miles north, in Chippewa Falls.
    There are about four new machine shops...
  8. Replies
    9
    Views
    1,093

    I have a customer who has me ship via their...

    I have a customer who has me ship via their account.

    The regular charge for Overnight! to Singapore are around $100

    Actual cost is well under $10

    So, BIG companies can get a Big discount.
  9. Since it is an interference engine, you HAVE to...

    Since it is an interference engine, you HAVE to have is all lined up BEFORE you bolt the head on.
    If you bolt on the head, Then turn the crank to the alignment position, ... CRUNCH!! into junk.
    If...
  10. The two PC motherboards are the WS (work station)...

    The two PC motherboards are the WS (work station) and the RT ( real time ) motherboards.

    The WS boots up, that is the one having trouble with the disk,
    Once it boots up, it downloads to the RT...
  11. Replies
    928
    Views
    36,255

    Fer crying out loud... Get A Grip !! Or a...

    Fer crying out loud... Get A Grip !!

    Or a valise.
  12. Thread: Fools Game

    by 3t3d
    Replies
    24
    Views
    2,219

    Sometimes I wonder if Hanermo feels like he is...

    Sometimes I wonder if Hanermo feels like he is driving mini van full of screaming, fighting brats through heavy traffic in a thunderstorm, in a construction zone.
    Or 100X worse trying to moderate...
  13. Same transmission for Ford or GM.

    Same transmission for Ford or GM.
  14. Replies
    928
    Views
    36,255

    The REAL QUESTION though is: Will Greenland stay...

    The REAL QUESTION though is:
    Will Greenland stay Metric or have to switch to Imperial measurements?

    I remember a ski trip in 1985 to Thunder Bay, (not Greenland, but it was a metric country)...
  15. Replies
    20
    Views
    2,701

    Can you limit the rotary table Wind up? That...

    Can you limit the rotary table Wind up?
    That would solve your problem.
  16. Some Perspective... Across the street from my...

    Some Perspective...

    Across the street from my shop last week there was some work going on...
    I looked over the see what was going on and it was like a Road Runner illusion. I couldn't focus my...
  17. Replies
    4
    Views
    913

    Solenoid Valve Cables & Connectors (Square DIN...

    Solenoid Valve Cables & Connectors (Square DIN Style) | Pneumatic Components | Products | AutomationDirect
  18. Bypass the cordless drill, and get a small...

    Bypass the cordless drill, and get a small brush-less motor from the hobby store.
  19. Replies
    2
    Views
    788

    That was a rough day... A few blocks from my...

    That was a rough day...
    A few blocks from my shop, the same day...
    5 dead, 2 injured after shootings in Lake Hallie and Lafayette | Crime and Courts | chippewa.com
  20. Replies
    86
    Views
    5,450

    This new Vette looks pretty good to me. Nice to...

    This new Vette looks pretty good to me. Nice to see New designs coming to light.

    I have long been curious about the Super Light Coup SLC from Race Car Replicas RCR
    It looked like something I...
  21. Thread: Copper Help

    by 3t3d
    Replies
    18
    Views
    1,485

    I was making a lot of .375" thick parts.. At...

    I was making a lot of .375" thick parts..
    At first I was profiling cutting down in steps in the Z direction.
    That would wear out the end of the end mill in a step pattern.
    Went to a tool path...
  22. Replies
    17
    Views
    2,483

    Once again some new guy shows up, asks an...

    Once again some new guy shows up, asks an innocent question, and someone has to start barking, growling, and lunging at the end of their chain after them.

    Why did I know this before I even read...
  23. Replies
    13
    Views
    1,635

    Rivett688, What are you doing with such an...

    Rivett688,
    What are you doing with such an Enormous tap?
  24. Scotchman Industries Phone...

    Scotchman Industries
    Phone: (605) 859-2542
  25. Thread: Copper Help

    by 3t3d
    Replies
    18
    Views
    1,485

    My customer would kill me if I tried to anneal...

    My customer would kill me if I tried to anneal the copper!

    They specified the hardness, NOT dead soft, annealed copper.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4