Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: agieman

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    447

    just my 2 cents. charmilles machines have...

    just my 2 cents. charmilles machines have collision protection. this can be a life saver for newbies! Also,they do not charge for phone support. if machine is still supported all calls are free. im...
  2. Replies
    17
    Views
    1,308

    i would keep the filter in if it generates an...

    i would keep the filter in if it generates an error msg open the opposite door and find the "spaceship" sensor at knee high height. jumper 2 wires together. your mode 6 problem is likely reference...
  3. Replies
    15
    Views
    1,027

    coolest i ever saw was about a 3in tall .5 in...

    coolest i ever saw was about a 3in tall .5 in "tornado" growing out of a cavity. pre cell phone day or y'all would see a picture!
  4. Replies
    15
    Views
    1,027

    you wont find much because "uncontrolled arcing...

    you wont find much because "uncontrolled arcing damage" leads to wire breakage and stops the process. It will create a line in your piece most likely and hardly a good representation of arcing...
  5. Replies
    17
    Views
    1,308

    Hi Clayton, glad to hear it! on the back bottom...

    Hi Clayton, glad to hear it! on the back bottom ground cable there was a small reference line included. did you replicate it?
  6. Replies
    17
    Views
    1,308

    Clayton what settings are you using they should...

    Clayton what settings are you using they should be
    EROS T M=5 t=5 I=13 pr=10 p=13-20 Td=25 HC=6
    EROS S cw=2 fw=17 Aw=120 B=1 K=10 Q=4 Str=2 Qo gage =5 bar. this is for CCA wire but brass will...
  7. Replies
    17
    Views
    1,308

    Hi Clayton, you are barking up the wrong tree on...

    Hi Clayton, you are barking up the wrong tree on that one. that is to retract wire after a break. Here's what to do
    thread the wire. with handbox on run the wire grab the black wheel and try and...
  8. Replies
    17
    Views
    1,308

    find Fm and UFS lines in schematics there is a...

    find Fm and UFS lines in schematics there is a wid board on back of machine that all spark cables come into. - is to the carbides + to the table
  9. Replies
    17
    Views
    1,308

    Hi Clayton, it is necessary to disconnect the the...

    Hi Clayton, it is necessary to disconnect the the long lengths of spark cable and main unit of generator in the SF (fine finishing) mode. there is a portion of the generator mounted in the machine...
  10. Replies
    17
    Views
    1,308

    Hi Clayton, your reference lines or fine module...

    Hi Clayton, your reference lines or fine module lines are open. do you have prints? check the gap boxes on the end of the upper and lower arms.There are 2 air lines to each box they should change...
  11. Thread: Agie 100 parts

    by agieman
    Replies
    12
    Views
    2,077

    THAT IS NOT AN AC100! that is a DEM315/2

    THAT IS NOT AN AC100! that is a DEM315/2
  12. Thread: Agie 100 parts

    by agieman
    Replies
    12
    Views
    2,077

    Andy you need to home the z axis then home u-v...

    Andy you need to home the z axis then home u-v axes. then z will go down.
  13. Replies
    15
    Views
    3,934

    hi Kevin the classic was made in Losone just like...

    hi Kevin the classic was made in Losone just like the challenge AND the machine tool is basically the same.
  14. Replies
    1
    Views
    464

    going from memory here but 140 is start in short...

    going from memory here but 140 is start in short ckt. i believe. check if there is continuity between wire and table. there should not be.
  15. Replies
    7
    Views
    739

    well you may be able to get training from GF for...

    well you may be able to get training from GF for that machine. if not you have us!
  16. Replies
    7
    Views
    1,004

    SERVICE OR APPS? Service may draw a hard line but...

    SERVICE OR APPS? Service may draw a hard line but try apps.
  17. Thread: Entry Cuts

    by agieman
    Replies
    3
    Views
    989

    FYI entry and exit settings are low power...

    FYI entry and exit settings are low power settings to compensate for poor initial flushing condition. On the entry page in machine details you can choose a tangental entry method and define a radius....
  18. this machine is basically a Classic 2S model. i...

    this machine is basically a Classic 2S model. i take care of some, what are your questions?
  19. Replies
    10
    Views
    1,223

    this message on the 50 and the 70 machines...

    this message on the 50 and the 70 machines indicate a ROM error. Reseat computer boards and replug connections.
  20. Replies
    10
    Views
    1,223

    this is wire EDM yes?

    this is wire EDM yes?
  21. Replies
    10
    Views
    1,223

    let me see what i can do. i have a few friends...

    let me see what i can do. i have a few friends who still have brothers.
  22. Replies
    10
    Views
    1,223

    this may be incredibly obvious but it doesn't...

    this may be incredibly obvious but it doesn't sound like it was fixed. have you talked to the repair person?
  23. Replies
    7
    Views
    1,101

    this is on the E machines. there is a gauge on...

    this is on the E machines. there is a gauge on the main cabinet for air pressure and filter pressure. on the P machines it is different. filter pressure is in consumables>dielectric section.
  24. Replies
    7
    Views
    1,101

    upper right of cabinet 2 gauges one for air and...

    upper right of cabinet 2 gauges one for air and one for filter pressure. 2.8 bar is where it alarms out. on the Gauge, because its x10 it will be .28 bar
  25. Replies
    2
    Views
    2,227

    Hi Guys, sorry been out for a few weeks. here is...

    Hi Guys, sorry been out for a few weeks. here is what i have and you are not gna like it
    255990
Results 1 to 25 of 269
Page 1 of 11 1 2 3 4