Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: SteveM

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. I'm not familiar with that machine, but if it has...

    I'm not familiar with that machine, but if it has a threaded spindle, you don't want to stop the spindle quickly, or your chuck can unscrew.

    If it's a D camlock, L-xx spindle or some other pinned...
  2. Replies
    6
    Views
    506

    Rex - collets came safe and sound. Thanks. ...

    Rex - collets came safe and sound. Thanks.

    Steve
  3. Replies
    6
    Views
    506

    Check your email, Rex. Steve

    Check your email, Rex.

    Steve
  4. Replies
    6
    Views
    506

    Rex, I have no duplicates in 5C and nothing I...

    Rex,

    I have no duplicates in 5C and nothing I have uses R8.

    I have dups in 3AT and B&S7.

    I can buy the collets outright if we can't find trades. Those two would be the most important missing...
  5. Replies
    0
    Views
    217

    Rivett 40S collet, 5/16

    A 5/16 Rivett 40S collet came in a box of other stuff.

    If anyone can use it, $10 plus shipping, or trade for 3C collets in the following sizes:

    1/16
    5/64
    11/64
    13/64
    1/4
    19/64
  6. Replies
    0
    Views
    170

    Rivett 40S collet, 5/16

    A 5/16 Rivett 40S collet came in a box of other stuff.

    If anyone can use it, $10 plus shipping, or trade for 3C collets in the following sizes:

    1/16
    5/64
    11/64
    13/64
    1/4
    19/64
  7. Replies
    6
    Views
    506

    3C collets needed, some to trade

    I am in need of the following 3C collets:

    1/16
    5/64
    11/64
    13/64
    1/4
    19/64
    21/64
    3/8
  8. Replies
    3
    Views
    751

    Not that it will help you, but if anyone needs...

    Not that it will help you, but if anyone needs one, I have one for a smaller set (30-something blocks).

    Steve
  9. Replies
    12
    Views
    1,486

    Someone is selling 3-d printed plastic ones on...

    Someone is selling 3-d printed plastic ones on fleabay.

    It's not like it's a part that takes a lot of loads, so for some people, it may last as long as the machine.

    Steve
  10. Thread: fine feed box?

    by SteveM
    Replies
    5
    Views
    982

    I'm no expert, but the only fine feed one I have...

    I'm no expert, but the only fine feed one I have seen is on the heavy 10.

    You can identify it by the left tumbler going from A to G instead of A to E.

    They didn't come on the 9" models.

    I...
  11. Post says: "Sorry, no paypal. Check or m/o is...

    Post says: "Sorry, no paypal. Check or m/o is fine"
  12. Replies
    15
    Views
    1,749

    When drilling with large drills (and I've drilled...

    When drilling with large drills (and I've drilled with 1" drills on my Atlas), I step up in small increments (like 1/16") so that the drill isn't doing too much work.

    Why do tailstocks not have...
  13. Replies
    289
    Views
    73,025

    I have to call this one the "Clown Lathe" because...

    I have to call this one the "Clown Lathe" because of all the different colors. It's like he didn't have enough of any one color to paint it.

    Steve
  14. Replies
    13
    Views
    2,388

    No you don't. The ends of the rods are pointy and...

    No you don't. The ends of the rods are pointy and sharp, and the spring is very strong compared to what you would see in something like a telescoping gauge.

    It digs in and stays put.

    Steve
  15. Replies
    26
    Views
    3,074

    Recently sold an item. Turned out a small part...

    Recently sold an item. Turned out a small part inside was broken, making it useless. Refunded the buyers total including shipping and didn't bother with returning it.

    Result was positive feedback...
  16. Replies
    26
    Views
    3,074

    I had a seller selling an item for $4 which would...

    I had a seller selling an item for $4 which would fit in a small flat rate box (actually four of them could) and the shipping was something like $25. They actually refused to use a flat-rate box....
  17. Replies
    11
    Views
    2,041

    Probably quite a bit more, since it's all the...

    Probably quite a bit more, since it's all the toolboxes and all the tools on the table.

    The Gerstner box would be $400, and that might be what you meant.

    Nice vise.

    $3,000, no way. How...
  18. Replies
    12
    Views
    1,264

    Yes, I just haven't gotten it up to the top of my...

    Yes, I just haven't gotten it up to the top of my list.

    This is for the P&W mill, and the adjustment screw needs to be offset to the side. There was one on ebay that went for cheap, but I didn't...
  19. Replies
    12
    Views
    1,264

    OK, rather than modifying a south bend part, let...

    OK, rather than modifying a south bend part, let Lazz have it.

    Steve
  20. Replies
    12
    Views
    1,264

    OK, what I need it to fit is 3-3/4 wide at the...

    OK, what I need it to fit is 3-3/4 wide at the outside of the dovetail, 2.75 in the valley and 4-1/4" across two 1/2" dowel pins.

    If that will fit, I'll take it.

    This would be for the vertical...
  21. Replies
    12
    Views
    1,264

    I'm interested if it fits. Be right back with...

    I'm interested if it fits.

    Be right back with measurements.

    Steve
  22. Replies
    0
    Views
    452

    Precision Devices Reference Standard PDR-6

    Here is a Precision Devices Reference Standard model PDR-6

    This is used for calibrating surface roughness gauges.

    It has separate surfaces marked "Calibration", "Linearity" and "Stylus Check"....
  23. Kennametal Drilling Inserts, dtf05t308bld, Form W, total of 16 inserts

    Here are some Kennametal drilling inserts. Three full boxes of five plus one extra.

    The grade is KC720, which is described by the manufacturer as:
    Composition: A tough, durable PVD TiN coating...
  24. Replies
    2
    Views
    622

    Band-it strapping tool, straps and buckles

    Band-it banding strapping tool. Package has no ZIP code, it so it dates to before 1966. The tool tightens and cuts Band-it stainless steel banding. Band-it is used for clamping hose, pipe, tanks,...
  25. Replies
    20
    Views
    2,833

    To make the most money, sell everything...

    To make the most money, sell everything separately.

    If you do that, it would be crime and we will hunt you down.

    My guess is that anyone looking to trade a Bridgeport is probably going to be...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4