Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: plastikdreams

Search: Search took 0.01 seconds.

  1. Replies
    39
    Views
    2,074

    I'll never know if it works, but I know I will if...

    I'll never know if it works, but I know I will if it doesn't
  2. Replies
    39
    Views
    2,074

    Nah it's some kind of thread in suction cup. :)

    Nah it's some kind of thread in suction cup. :)
  3. Replies
    39
    Views
    2,074

    The one engineers reply was, if it's too lose...

    The one engineers reply was, if it's too lose we'll use Teflon tape...it's out of my hands now.
  4. Replies
    39
    Views
    2,074

    For sng here's picture from my mh for tap drill...

    For sng here's picture from my mh for tap drill sizes for American thread forms

    315763
  5. Replies
    39
    Views
    2,074

    Pretty much...that's why I asked. And if you...

    Pretty much...that's why I asked. And if you actually READ my op I had an answer I was just double checking. :rolleyes5:



    Sure lol like I said I have 0 experience with bsp :)
  6. Replies
    39
    Views
    2,074

    Bsp wasn't even remotely in the equation...I've...

    Bsp wasn't even remotely in the equation...I've never even threaded anything bsp. Funny thing is, they brought me 2 taps and a similar part that would thread into the block. The nut on the part...
  7. Replies
    39
    Views
    2,074

    1/8 bsp straight.

    1/8 bsp straight.
  8. Replies
    39
    Views
    2,074

    It can be a shitshow here one engineer from dept...

    It can be a shitshow here one engineer from dept a specifies something being made for dept b but then an engineer from dept b says its supposed to be something else...then we can't get the 2 of them...
  9. Replies
    39
    Views
    2,074

    Ended up being 1/8 bsp thread lol.

    Ended up being 1/8 bsp thread lol.
  10. Replies
    39
    Views
    2,074

    I didn't see 28 in my mh v28. But looks like the...

    I didn't see 28 in my mh v28. But looks like the numbers match up. Looks like they are going to use a nut to tighten up some threaded suction cups to hold vacuum. I guess npt wasn't good enough...
  11. Replies
    39
    Views
    2,074

    Thanks guys...I'm waiting for some clarification...

    Thanks guys...I'm waiting for some clarification on a couple things...
  12. Replies
    39
    Views
    2,074

    The book shows 3/8-27 and R drill...how much you...

    The book shows 3/8-27 and R drill...how much you wanna bet the engineer wrote the wrong number lol.
  13. Replies
    39
    Views
    2,074

    I do, I didn't even think to look there...way to...

    I do, I didn't even think to look there...way to make me feel like a dumbass lol

    :)
  14. Replies
    39
    Views
    2,074

    Tap drill for 3/8-28 tap

    I have to tap 2 holes 3/8-28. All the drill charts I've found do not have this size. Per the ghuring site it recommends .340 for the hole size at 75%, which is basically a letter R (.339) drill. Does...
Results 1 to 14 of 14