Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.10 seconds.

  1. I used lether shoelaces when I did a lot of torch...

    I used lether shoelaces when I did a lot of torch cutting
    Also neck protection when welding or torching over your head
    Oh yes And I still have leather workshoes :D

    Peter
  2. Replies
    14
    Views
    433

    What is your powersource 240Volts single phase...

    What is your powersource
    240Volts single phase ???
    What fuses does it have
    Do the fuses trip or the VFD?
    What voltage is the motor ??
    Dual voltage single speed or dual speed single voltage ??...
  3. Replies
    4
    Views
    311

    Or it has a adaptor MT4 to R8 Who knows Peter

    Or it has a adaptor MT4 to R8
    Who knows

    Peter
  4. Replies
    19
    Views
    1,454

    It looks to me like it is your motor But not...

    It looks to me like it is your motor
    But not 100% sure
    It could be its a bit of both
    Peter
  5. Replies
    19
    Views
    1,454

    I would have checked(with motor running at best)...

    I would have checked(with motor running at best)
    L1 to L2
    L2 to L3
    L1 to L3
    That is what the motor feels
    I suspect it is off too

    Peter
  6. The older version has a MT4 spindle While the...

    The older version has a MT4 spindle While the later ones have a Iso 40 taper
    If it has a Iso 40 taper the price is right For a MT4 it depends
    And they have a quill
    Parts are still available ...
  7. Replies
    37
    Views
    2,138

    The Italians are that crazy I noticed before on...

    The Italians are that crazy
    I noticed before on other Italian lathes to have a right hand tread on their tailstocks

    Peter
  8. Replies
    37
    Views
    2,138

    I dubblechecked on 2 Sag12 one Sag12S and a Maho...

    I dubblechecked on 2 Sag12 one Sag12S and a Maho Graziano100W I have here
    Sag12 and Sag12S have the abnormal right hand tread on the tailstock
    The Maho Graziano100W has the normal left hand...
  9. Replies
    37
    Views
    2,138

    Hello Noam The Graziano is different from...

    Hello Noam

    The Graziano is different from most lathes with having a right hand thread in the tailstock yes
    I have to check on the handle that pulls out tomorrow
    I can check if the SAG12 has...
  10. You could also linebore it:willy_nilly: Drilling...

    You could also linebore it:willy_nilly:
    Drilling it bigger say 2,5mm about 4 mm deep thats where I would start

    Peter
  11. Yes indeed and the inner part is a bit shorter as...

    Yes indeed and the inner part is a bit shorter as the copper shell
    So with drilling the holes of your rosebud a bit bigger you get the same idea

    Peter
  12. What I was told is to drill the holes twice as...

    What I was told is to drill the holes twice as big just a few mm deep
    That will preheat the propane somewhat

    Peter
  13. Lye might work Or not Or paint thinner covered...

    Lye might work Or not
    Or paint thinner covered with plastic so it does not evaporate that quick
    Best outdoors It can be unhealty like most things in life. In fact living is dangerous You die of...
  14. With 0.06mm endplay one can assume the spindle...

    With 0.06mm endplay one can assume the spindle needs a rebuild
    That involves grinding and lapping the spindle Then scrape the bearing
    On a Aba the OD of the plain bearing is tapered and has 3...
  15. I was looking for that dokumentation I cannot...

    I was looking for that dokumentation
    I cannot find it right now
    I have a further look

    Peter
  16. On a bandsaw with tires you can use saws of...

    On a bandsaw with tires you can use saws of different width The teeth ride on the softer material from the tires and don`t get smashed therefore
    The tires wear out though
    Bandsaws with no tires...
  17. 0.0025" Translated into metric that is more as ...

    0.0025"
    Translated into metric that is more as 0.06mm
    You better put grease in it :)
    0.01mm was recommended by Aba IIRC
    And then the right oil Thinner as water
    In old documentation they...
  18. Replies
    20
    Views
    3,416

    Perhaps the other way around The surface plate...

    Perhaps the other way around
    The surface plate to the magnet :)

    Peter
  19. You could also buy a rebuild Leinen DLZ140 from...

    You could also buy a rebuild Leinen DLZ140 from Rümema Germany
    Very accurate machine
    You defenitly need a DRO on it capable of reading 0.001mm
    Drehmaschinen von Ruemema
    Peter
  20. Replies
    37
    Views
    2,138

    There is a keyway in the handle So feeling the...

    There is a keyway in the handle So feeling the detent positionion is not a issue
    For me it was a 1minute job for each handle Oke 2 min perhaps

    BTW All the rings on the back of the handles have...
  21. Replies
    37
    Views
    2,138

    Sizes are not critical But here is a rough...

    Sizes are not critical But here is a rough drawing of thehalf ball part I send to my machineshop
    The handlepart is 20mm round stock machined with a 8mm radius (16mm endmill) to fit the 8mm gap in...
  22. Says who???

    Says who???
  23. Replies
    14
    Views
    1,502

    This is a situation that I would do it otherwise ...

    This is a situation that I would do it otherwise Turcite on the stationary part. That is why I tend to say turcite on the smaller/shorter part
    The few times I did pull scrape turcite I used my...
  24. Replies
    14
    Views
    1,502

    In general the moving part is the shortest part...

    In general the moving part is the shortest part and therefore the turcite always stays covered
    That is the important part
    Not a good idea to glue turcite on the bedways of a lathe and expose the...
  25. Replies
    37
    Views
    2,138

    The brass cones are there only to keep those...

    The brass cones are there only to keep those handles on the shaft Not to take any torque
    It has a keyway like you see on my pictures in post 4 So I do not have any problems with that
    The original...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4