Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Scruffy887

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    4
    Views
    354

    Disposable class spindle? I am pretty sure they...

    Disposable class spindle? I am pretty sure they are pressed in.
  2. Replies
    10
    Views
    444

    It can cut steel with a carbide dry cut blade. At...

    It can cut steel with a carbide dry cut blade. At highest speed and hearing protection needed. Eye protection too. No coolant. But your results may vary.
  3. Right on. Have some more mushrooms.

    Right on. Have some more mushrooms.
  4. Replies
    34
    Views
    1,068

    I think we are feeding a troll here. OP needs to...

    I think we are feeding a troll here. OP needs to do a LOT more reading on the subject before asking questions. By doing so the OP will be able to ask intelligent questions, get intelligent answers.
  5. Well, fact checkers and my own memory of history,...

    Well, fact checkers and my own memory of history, and a lack of him ever saying things that are true in the last few months? He needs to lick the handrails and kiss everybody, shake their hands, of...
  6. Replies
    34
    Views
    1,068

    Its not that we cannot answer your questions....

    Its not that we cannot answer your questions. Your knowledge on the subject is so very weak that you cannot ask the right question. Get your feet wet with one of those $400.00 units on Amazon.
  7. Replies
    35
    Views
    1,258

    I watched a guy doing dados on a RA. Big Dewalt...

    I watched a guy doing dados on a RA. Big Dewalt too. Right hand on motor handle. Left had to the right of the blade holding stock and left elbow holding stock to the left of the blade. He never got...
  8. Replies
    61
    Views
    41,969

    No need for a stud finder. HERE I AM LADIES!...

    No need for a stud finder. HERE I AM LADIES! Seriously, yellow Zircon unit with the 9 volt battery. I would pick up a wall cabinet and place it on my install cart. Put the stud finder and a level in...
  9. The granite was glued to the cabinets with dabs...

    The granite was glued to the cabinets with dabs of silicon. Success of trying to move down the stairs with tops attached is very low. Cabinets may separate with granite also breaking. You need to...
  10. Replies
    8
    Views
    407

    Look on Craig's List for a tread mill. Speed...

    Look on Craig's List for a tread mill. Speed control and a lot of other goodies included. Overweight people will pay you to get them out of their basement. But some will keep them if the bars hold...
  11. Replies
    154
    Views
    8,274

    No audit under 2 million. I am light years away...

    No audit under 2 million. I am light years away from that.
  12. Replies
    154
    Views
    8,274

    It is what you pay them per week. If they get...

    It is what you pay them per week. If they get vacation pay, holiday pay, sams club, hookers and blow, you apply for that. If you get it you have to give it to them. Assuming hookers and blow are...
  13. Replies
    154
    Views
    8,274

    PPP is also for economic uncertainty and we all...

    PPP is also for economic uncertainty and we all have that. Maybe not now but it is coming. And it is also because small businesses like mine may not be able to get a loan during these times, no...
  14. Replies
    154
    Views
    8,274

    That may be true here as well, but UI checks are...

    That may be true here as well, but UI checks are based upon gross pay, not hourly rate. That being said I need to check on the paperwork that the state sent to me. If he listed that he works a 40...
  15. Replies
    154
    Views
    8,274

    Thursday my 2 men that are out got their direct...

    Thursday my 2 men that are out got their direct deposit. Friday morning at breakfast a text message comes in. Something is wrong with my pay can i get a pay stub (that is how he wrote it) I know...
  16. SBA had a new ruling that any companies getting...

    SBA had a new ruling that any companies getting funded less than two million had a Safe Harbor. The reason is that there for sure is economic uncertainty, and companies that size would have little...
  17. They machine lubricating plastics. I do a lot of...

    They machine lubricating plastics. I do a lot of that also. Tool life in decades, even with HSS. Corian is very abrasive. But if you have a heavy high speed router it can be machined very fast. My...
  18. You could try a hack around by machining a hex in...

    You could try a hack around by machining a hex in the main or sub jaws to grab at the 9 degrees difference. But I drank the Mazak coolade long ago and have jaw rotation and sync in many programs. I...
  19. Un coated carbide or diamond tipped when you get...

    Un coated carbide or diamond tipped when you get to that point. 8000 will do it. Dry with dust extraction. Corian is a filled acrylic, ATH is the filler. It will not melt like acrylic as the filler...
  20. Replies
    33
    Views
    6,825

    Thomas pump. Guy who sells pumps wants the bigger...

    Thomas pump. Guy who sells pumps wants the bigger profit from a bigger pump. Efficient design requires EPDM sponge cord for gaskets. I use .250 and .375. Cut ends square with a razor and super glue...
  21. Replies
    33
    Views
    6,825

    1/15 HP diaphragm vacuum pump can do a real good...

    1/15 HP diaphragm vacuum pump can do a real good job and sounds like a fish tank pump on steroids. They last about 8-10,000 hours. $210.00 and pull 25 inches. You would need a 3/4 HP compressor to...
  22. His reason was not related to my credit rating....

    His reason was not related to my credit rating. But yes, need to change to a local bank in the near future.
  23. Some of these rules are in effect based upon when...

    Some of these rules are in effect based upon when you applied. When I applied the reason for the loan/grant was to get your employees off the State UI roll because the states will run out of money...
  24. Replies
    17
    Views
    1,174

    I run 2" bars through the spindle. Doing it for...

    I run 2" bars through the spindle. Doing it for years and the full length of the spindle. I use spindle liners to keep centered and balanced. Most of my parts are finished by the sub spindle, but...
  25. VERY interesting PPP video. Watch your back.

    YouTube

    Give out the money and say it is free. Then change the rules.
    So if you got funded early, and paid your people to stay home? That amount may not be forgiven if your business was...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4