Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: SchneiderMachine

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    5,435

    The pin is to lock it on center as you have found...

    The pin is to lock it on center as you have found out. It came with a plastic fitted box, locking it on center makes it easier to get in and out of the box. That is all I've found it useful for....
  2. Sam, the jumper is not needed. You probably blew...

    Sam, the jumper is not needed. You probably blew a fuse with that setup. Incoming 220 on 1 and 3, skip the middle all together.
    Don't need anything special for the spindle drive (vfd)
    Been running...
  3. I'll look at my drive tomorrow night, I think...

    I'll look at my drive tomorrow night, I think it's the same one or close to it. The guy at drives warehouse helped me get mine up and running and I fine tuned it from there. Mine does not have rigid...
  4. Drives Warehouse, replace that thing with a...

    Drives Warehouse, replace that thing with a Hitachi drive.
    Had a magnatek gp3 rebuilt by profix, cost about 730 and change, lasted about 4 yrs and dies again. New hitachi drive 750 to my door.
    Dave
  5. Picture 7 B) Mitutoyo 5-6" .0001 the pad rotted...

    Picture 7
    B) Mitutoyo 5-6" .0001 the pad rotted and stained the mic works well $25
    Add this also.
    Let me know the total sir.
    Dave
  6. Pic 7D and 5J PM Me, Dave Paypal??? Don't...

    Pic 7D and 5J
    PM Me,
    Dave

    Paypal??? Don't remember
  7. Replies
    56
    Views
    5,489

    Well, having communication downtime may cause...

    Well, having communication downtime may cause some data gaps, it would still be better than not finding the black box at all.
    My .02 anyway
    Dave
  8. PM'd about this, A) Central tool ( USA) 1"...

    PM'd about this,
    A) Central tool ( USA) 1" indicator complete,works well,dirty box $30

    Dave
  9. Replies
    42
    Views
    7,509

    Boy, you guys are making a mountain out of a mole...

    Boy, you guys are making a mountain out of a mole hill, do what ever works man, who cares if Bob, Bill or Joe wont do it that way but Gerhard, John and Steve does. Get the job done man!! Don't over...
  10. Check the memory chips in the black box inside...

    Check the memory chips in the black box inside the machine, make sure they are seated all the way, I had that same problem once, turned out 1 chip was partially seated.
    Dave
  11. Drawbar is a piece of cake to fix. Probably a few...

    Drawbar is a piece of cake to fix. Probably a few broken belleville washers in there.
    Dave
  12. Milltronics won't do ANY thing for their...

    Milltronics won't do ANY thing for their customers anymore, all done through the reseller. They are going to hell in a hand basket. I know of a shop that had a lot of their machines, they are being...
  13. I take an edge finder also, I'll toss in the...

    I take an edge finder also, I'll toss in the extra 8 bucks in you paypal.
    Dave
  14. Will take all of these, Brown & Sharp Pr 1x2x3...

    Will take all of these,

    Brown & Sharp Pr 1x2x3 blocks $35
    Import 1x2x3 Pr blocks $10 X2

    And these
    Starrett S191 PR screw jacks good as new $40
    enough thread files to make a decent set

    PM...
  15. Replies
    35
    Views
    17,984

    The EzCam stuff ran on the RISC processor,...

    The EzCam stuff ran on the RISC processor, MeshCam and NX need the Intel processor.
    FWIW,
    Dave
  16. Since I got dragged into this dilemma I went over...

    Since I got dragged into this dilemma I went over to Techguys place and we decided the best way to fix the problem was to re-install the spindle upside down, problem solved.
    nyuck nyuck
  17. Oh, so a phase 2 just wasn't good enough for ya...

    Oh, so a phase 2 just wasn't good enough for ya huh. Just had to one up me, see how you are.
    hehehehehehe
    :D
    Dave
  18. Replies
    6
    Views
    2,383

    Mastercam editor can run independant from the...

    Mastercam editor can run independant from the main program. I've used the free dnc programs, sometimes they're not as stable
  19. Replies
    6
    Views
    2,383

    I use it for sending and receiving, didn't try...

    I use it for sending and receiving, didn't try the dnc part yet but I'd bet it's just fine. Not any different than anything else. And it's included with the editor so you don't have to buy anything...
  20. The program switches from absolute to incremental...

    The program switches from absolute to incremental so any typos in the incremental part would/could cause a problem
    Dave
  21. Hi Bill, I figured he was comping all the tool,...

    Hi Bill,
    I figured he was comping all the tool, there in lies the problem "I think" as I've seen that problem before, cutting only 1 side. Not going to rule out a mechanical issue though either "or"...
  22. Fixed your code, the red parts. Should terminate...

    Fixed your code, the red parts. Should terminate properly now. I've seen cutter comp act funny, as in, only cutting on 1 side, especially if your trying to comp to much of the tool. Sometimes it's...
  23. Replies
    7
    Views
    3,415

    I have a Takasawa TC-1 with a Fanuc 0T-C circa...

    I have a Takasawa TC-1 with a Fanuc 0T-C circa 1989 (IIRC) and it runs and runs, great iron, fast but small. FWIW

    Dave
  24. Replies
    27
    Views
    5,674

    Hmm, I believe the Bestest is made by Tesa, but...

    Hmm, I believe the Bestest is made by Tesa, but yes, both made by the Swiss albeit not the same factory.
    Dave
  25. Yes sir, 10 miles from Waconia. Sent you a pm...

    Yes sir, 10 miles from Waconia.
    Sent you a pm
    Dave
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4