Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: timopen

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    1,026

    There are "grease guns" meant for oil. For...

    There are "grease guns" meant for oil. For example Pressol 12602.
  2. I have the zerk up there where the manual states....

    I have the zerk up there where the manual states. I cannot see even a hole in your picture where it should be. :nutter:
  3. http://www.sarm.am/docs/10226-1-2004.pdf Edit:...

    http://www.sarm.am/docs/10226-1-2004.pdf

    Edit:
    These were also there
    http://www.sarm.am/docs/10226-2-2005.pdf
    http://www.sarm.am/docs/EN%2010226-3_2005_e_stf.pdf
  4. Replies
    72
    Views
    28,925

    Steel trees seem to grow with more optimum cross...

    Steel trees seem to grow with more optimum cross section for structural purposes than wooden trees :confused:
  5. Replies
    15
    Views
    1,736

    Well... it might be that there is no specific...

    Well... it might be that there is no specific equation for large radius bending.

    I know something about plate work, but not so much...

    But, if read correctly... you didn't give information...
  6. Replies
    285
    Views
    29,534

    I have Mori Seiki SL-1 that I retrofitted with...

    I have Mori Seiki SL-1 that I retrofitted with taiwanese LNC cnc controller and some older Omron servomotors and drives. At the end it was simple task that took hell of a time because of the learning...
  7. Replies
    7
    Views
    1,486

    I would change material to austenitic stainless...

    I would change material to austenitic stainless steels, maybe job profit would also go higher.

    (sorry this was just a joke, I just hate my bandsaw and all the problems with it, and I'm drunk.)
    ...
  8. Can these parts be made with live tooled or swiss type lathe?

    Hi,

    hopefully the topic of this thread is not meaningless, but I didn't figure out better one.

    So here's the picture of the parts I made about a year ago.

    148619

    Material is round stock...
  9. Thank you all for your replies! Well I try to...

    Thank you all for your replies!

    Well I try to answer some questions here:

    First of all this is a manual machine with age of 42 years (manufactured in 1972). I purchased it from school and I'm...
  10. Small vibration pattern surface finish problem at turning

    Just yesterday night I started to pay attention at the surface finish of the parts I turned. Finish is probably good enough and I cant feel the vibration that is shown in pictures when I touch the...
  11. Replies
    1
    Views
    1,405

    Deep hole drilling, 309 Stainless Steel

    Hi,

    I'm quoting for 8 parts that are made from EN 1.4828 (309 at AISI/ANSI?). Those are basically a shaft with a through hole, but the material and dimensions of the hole makes me wonder. The hole...
  12. Did you make a new lever to the 4-way-joystick?...

    Did you make a new lever to the 4-way-joystick? We have TOS SN50B at the work and though the lever is about 150...200mm long it's still kind a stiff to activate...
  13. Replies
    47
    Views
    30,654

    I think CNC could do it in any way. In picture...

    I think CNC could do it in any way. In picture below there are ways that have been presented in lecture slides at universitys basic machining course (not sure from where the picture is borrowed to...
  14. Replies
    47
    Views
    30,654

    I have only turned few threads so I'm not expert...

    I have only turned few threads so I'm not expert to comment practical situation... I understand that setting compound to angle smaller than 1/2 the thread angle enables back of the tool (assumed to...
  15. Thank you. Capacity of the bottle jack is 5 tons....

    Thank you. Capacity of the bottle jack is 5 tons. Capacity of the frame or toe isn't probably that much... well depending on how close you can get corner of the toe to lift. I assume that the plates...
  16. And I had to add picture of them in action :-)...

    And I had to add picture of them in action :-) moving my W&S #3... wondering if there is any other in Finland :-)
  17. Build two of these. Plates are 16mm thick and toe...

    Build two of these. Plates are 16mm thick and toe was welded in K-groove... root with GTAW and upper beads with GMAW.
  18. Replies
    13
    Views
    2,698

    Not exactly the similar case, but I repaired...

    Not exactly the similar case, but I repaired "nut-pocket" of the compound of my lathe with way shown in pictures below. Might work for your case... counterbores for allen screws and maybe some...
Results 1 to 18 of 18