Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cal Haines

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Go back and read what I wrote in post #82...

    Go back and read what I wrote in post #82. It's not at all clear to me that you have any problem with the R-N-L selector on the top or the microswitches in the casting. The selector isn't supposed...
  2. Replies
    58
    Views
    2,061

    It appears to me that someone has been messing...

    It appears to me that someone has been messing with the wires that connect to the movable fingers. See how the one on the far left comes into the crimp from the TOP? I seriously doubt that's...
  3. For Monarch 10ee Lathe...

    For Monarch 10ee Lathe
  4. Yes, that's the switch. Thanks. Cal

    Yes, that's the switch. Thanks.

    Cal
  5. Replies
    10
    Views
    886

    I don't know when they changed things so that you...

    I don't know when they changed things so that you can't download the pictures.

    If we're talking about the box that's been grafted onto the tombstone on the front of the headstock, that has nothing...
  6. I don't see any need for it either. I also...

    I don't see any need for it either. I also haven't heard from anyone else who had a wire C-clip on their leadscrew. I could be that someone on third shift put one on when it wasn't supposed to be...
  7. Even if you could find a source, I would steer...

    Even if you could find a source, I would steer away from them. I had one of those damn things on the right end of the leadscrew on my 10EE. It was behind a stamped steel cap that had no provision to...
  8. I does appear that a 2-pole switch was used. If...

    I does appear that a 2-pole switch was used. If you look at drawing EE-3216, the section of the "Elementary Diagram" in the upper-right corner shows the drum switch and pump motor. Power for the pump...
  9. Tom, This photo shows the transformer on the...

    Tom,

    This photo shows the transformer on the left side of the frame; it's only function is to provide voltage to the start button pilot light:...
  10. I assume that these are in the end of the base...

    I assume that these are in the end of the base casting, above the big cover for the exciter end of the motor/generator. Those were probably for some user-installed accessory, perhaps a collet rack or...
  11. Replies
    35
    Views
    1,611

    If there's no run capacitors, I think it's...

    If there's no run capacitors, I think it's derated to 66%. Properly balanced run caps will improve that.

    You could test it by using a manually operated switch to temporarily connect a starting...
  12. Correct, Mobil. No, their tech support won't be...

    Correct, Mobil. No, their tech support won't be able to help you here.

    Sundstrand is still around (link). Have you tried them?

    Cal
  13. Mobile has gone through a progression of names....

    Mobile has gone through a progression of names. It started out as The Vacuum Oil Company in 1866, became Socony-Vacuum Oil, then Mobile, now Exxon-Mobile. Over the years the products have also gone...
  14. Replies
    15
    Views
    1,177

    That's a pretty cool chuck, but it looks like...

    That's a pretty cool chuck, but it looks like you'd be into it for over $4k, not including backplate.

    Cal
  15. Replies
    15
    Views
    1,177

    Have you considered using soft-jaws, bored to the...

    Have you considered using soft-jaws, bored to the correct OD? If you bore the jaws and don't remove the chuck, it will have zero runout.

    Depending on the what the part is, a large diameter,...
  16. Replies
    35
    Views
    1,611

    Based on the connections, it's probably a...

    Based on the connections, it's probably a standard dual-voltage, 9-wire motor, connected for high voltage:
    280820

    If you've got a rotary phase converter or access to 3-phase, you probably won't...
  17. Since this is an hydraulic drive, I think I would...

    Since this is an hydraulic drive, I think I would go with Mobil DTE 26, ISO 68 hydraulic oil. McMaster carries it: McMaster part #2158K13

    Cal
  18. Replies
    58
    Views
    3,402

    I'm 99.9% sure that's the right coil. I have a...

    I'm 99.9% sure that's the right coil. I have a photo of a 440V 60CY starter coil that has "464-3" on the second line; yours is "464-2". I'm guessing that the "464" is the coil form and the "-X"...
  19. Replies
    7
    Views
    714

    I think that if the combined weight of your 10EE...

    I think that if the combined weight of your 10EE tooling exceeds the that of the machine, you qualify. :D

    Cal
  20. Replies
    7
    Views
    714

    I think that you have everything. The other dial...

    I think that you have everything. The other dial like this that showed up (on EE27264) was an accumulating dial, with an extra ring/dial and a gear train that rotated the secondary ring so that you...
  21. Replies
    58
    Views
    3,402

    The original 10EE AC contactor/starter is a...

    The original 10EE AC contactor/starter is a Cutler-Hammer (CH) No. 9586H1990A6, size 1. Bulletin 9586 covers a whole bunch of options. Unfortunately, I've never been able to lay my hands on a copy of...
  22. Replies
    58
    Views
    3,402

    Probably to the coolant pump. Look in the...

    Probably to the coolant pump. Look in the compartment behind the big cover on the back and see if the pump is still there.

    Cal
  23. Replies
    58
    Views
    3,402

    https://www.practicalmachinist.com/vb/attachments/...

    https://www.practicalmachinist.com/vb/attachments/f10/280498d1583073434-1942-10ee-sight-unseen-ac-panel03.jpg

    The motor/generator (MG) is wired for 240, but that's only part of it. You need to...
  24. Replies
    58
    Views
    3,402

    The first batch of piggyback exciter 10EEs, circa...

    Two things I have not seen before - perhaps others have:

    UNDER driven exciter. I've only seen them with pulleys @ 1:1 or so they appear to be.

    TRIPLE vee-belts, motor to spindle.[/QUOTE]
    The...
  25. Replies
    58
    Views
    3,402

    I don't think you can tell anything from the...

    I don't think you can tell anything from the build plates and dials. I can show you examples on either side, by both serial number and build date, with about any combination of plates and dials that...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4