Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: _EMF_

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    1,157

    Thanks I'll give it a shot.

    Thanks I'll give it a shot.
  2. Replies
    13
    Views
    1,157

    I was going to ask you about it, also a video...

    I was going to ask you about it, also a video about putting an optional stop after some functions, so you can do a quick size check or clean chips out then carry on without stopping and starting the...
  3. Replies
    13
    Views
    1,157

    Just thought I'd throw this out there, in case...

    Just thought I'd throw this out there, in case someone is reading this trying to figure out their new T-2 and they're used to a T-32 or newer. First off it didn't come with a programing manual. I...
  4. Replies
    13
    Views
    1,157

    Thanks again I got it working by telling it what...

    Thanks again I got it working by telling it what gear to pretend to be in. I had to add two lines as well or it just stopped slightly above the part.
    G00 X5 Y5 M5 and G00 X5 Y5 M1
    ...
  5. Replies
    13
    Views
    1,157

    I took the s 500 out and it still threw the code...

    I took the s 500 out and it still threw the code and then I added gear 1 and it worked in simulation. I just had a tool eye finally give up the ghost on another older machine so I'm going to replace...
  6. Replies
    13
    Views
    1,157

    This machine doesn't have a gear box on it. So...

    This machine doesn't have a gear box on it. So would that still apply?
  7. Replies
    13
    Views
    1,157

    honestly I don't know why the s500 is in there. I...

    honestly I don't know why the s500 is in there. I never had an operators manual. I just took bits and pieces from a few old programs and started punching numbers into my other machine over 15 years...
  8. Replies
    13
    Views
    1,157

    This is a shot of my T-32 screen with the MNP...

    This is a shot of my T-32 screen with the MNP command that has worked for me for the last 15 years. I've been able to muttle through learning/re learning the new to me T2 control by watching...
  9. Replies
    13
    Views
    1,157

    T2 programing help

    I'm stumped. I just need to get the program to optionally stop so I can measure the part before I part it off. On my T-32 and T Plus controls I've always just used the MNP process. It moves the...
  10. I think I figured it out. there's about 4...

    I think I figured it out. there's about 4 materials that are pre set in the machine. Then you can enter your own. They are high lighted in a different color and don't show up on your display while...
  11. Awesome videos. I've been watching them all...

    Awesome videos. I've been watching them all night. Things that are confusing me are. the material settings in the the lathe cutting conditions. Are they pre set? I tried adding 4140 and it doesn't...
  12. MNP 1 On my T-32 and T-plus or it rotates the...

    MNP 1 On my T-32 and T-plus or it rotates the tool into the work piece or chuck right?
  13. Okay so I define the O.D. max in the first line...

    Okay so I define the O.D. max in the first line of the program to say 6". The tail stock is is under that.

    1) do I have to use that 6" diameter in the CPT X line in the first bar out line?
    2)...
  14. Mazatrol Cam T-2 Tool Path or hacks to control the path

    I just bought a mint QT -25 and am just familiarizing myself with the programing. I'm pretty good with my T-32 and getting better with the T-plus. I use the TPC to avoid my tail stock with those...
  15. I've been busy and this got put on the back...

    I've been busy and this got put on the back burner. It looks like the QX141 card was changed prior to it showing up here. I'm going to change the battery just because. I'm also going to send the...
  16. so you should still be able to get to the...

    so you should still be able to get to the parameter page. It wouldn't stop at the screen that pops up when you first turn it on? as well your control panel would still work? I think it has a bad card...
  17. What are the symptoms of lost Parameters with a T Plus control

    I'm just trying to find a starting point with this qt 20. It sat with no power for at least 6- 8 months. It had issues before I bought it. I honestly bought it for parts for my other QT 20. However...
  18. Replies
    6
    Views
    624

    A temporary fix to keep you going is to open the...

    A temporary fix to keep you going is to open the electrical cabinet and put a fan there to cool the drive. My QT 28 does that due to a weak fan on my NC unit which causes a connection issue between...
  19. Replies
    1
    Views
    330

    T Plus fire up issues. Dead battery?

    I'm trying to turn on a QT 20 that I bought and let sit for 7 or so months. There's power to the drives, the screen turns on to the home screen and stays there. There's no power to the controls ,at...
  20. Replies
    7
    Views
    1,279

    Unfortunately I have everything but the ladder...

    Unfortunately I have everything but the ladder manual. I have ladder manuals for my T-plus machines but I'm guessing the T-32 is different. I had it but a tech years ago, took it home to read it and...
  21. Replies
    7
    Views
    1,279

    also does anyone know what machine parameter T 51...

    also does anyone know what machine parameter T 51 does?
  22. Replies
    7
    Views
    1,279

    and thanks for the reply.

    and thanks for the reply.
  23. Replies
    7
    Views
    1,279

    The power supply (SF-PW) has an amber LED towards...

    The power supply (SF-PW) has an amber LED towards the left side if you look under the housing before you power up. The spindle drive has one red and amber LED and on the digital read out it shows a ...
  24. Replies
    7
    Views
    1,279

    does anyone know the address in the diagnosis...

    does anyone know the address in the diagnosis screen to see if the drive is seeing the e-stop?
  25. Replies
    7
    Views
    1,279

    T-32 emergency stop. Can't find the cause.

    Hi. I'm stumped. Machine is an old quickturn 28N. I've owned it for about 15 years.It's like my best friend. We've had our ups and downs. All the drives have been changed over the years. Power...
Results 1 to 25 of 29
Page 1 of 2 1 2