Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: CarbideBob

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    3,698
    Views
    92,462

    Tell us about how many IRS audits or worse you...

    Tell us about how many IRS audits or worse you have been through. Maybe there is none but do tell us.
    The first one is big fear and and crazy worry and you give when you should not and as here on...
  2. MRR at a point in time or across the entire part...

    MRR at a point in time or across the entire part cycle?
    Or across an hour or two where one includes part change, size adjust. dress and other fiddling.
    Did the part start as a cone?
    In the end...
  3. Why... I do ask that seriously.

    Why... I do ask that seriously.
  4. Negatives? Bad experience? I does not fit in...

    Negatives? Bad experience?
    I does not fit in some places and can be an increased cost and pain to the checkbook.
    If you can not cycle what is in that vend machine in two, three months or less its a...
  5. Replies
    21
    Views
    1,570

    I had to google left hand throttle on a...

    I had to google left hand throttle on a snowmobile to even know the what and why.
    Benn so many. many years since riding competition but I have been riding sleds since about 1964 when dad built one...
  6. Replies
    3,698
    Views
    92,462

    Two nights a week for two years and one night a...

    Two nights a week for two years and one night a week for four years seems about a wash to me.
    I do have a question for those that have done it.
    If such class put you into overtime were you paid OT...
  7. Replies
    25
    Views
    1,818

    oops..........

    oops..........
  8. Replies
    562
    Views
    66,958

    How will that work? Miles from what source of...

    How will that work? Miles from what source of information?
  9. Replies
    25
    Views
    1,818

    Just as an opinion from the sidelines I think...

    Just as an opinion from the sidelines I think dual contact in a Cat is way overrated and never proven real world.
    It is a very great marketing tool and sure seems like a good idea.
    As Alice was...
  10. Replies
    18
    Views
    1,698

    Opposite side of the coin. What do you do if you...

    Opposite side of the coin.
    What do you do if you are the outside op?
    Say a customer sends you parts and you are to drill a hole or two. Lets say a couple dollars to you on a ten to four hundred...
  11. In order for this this to work well and profit I...

    In order for this this to work well and profit I think you need to be train cars full and certainly not just one or two.
  12. Replies
    25
    Views
    1,818

    Why.........

    Why.........
  13. Replies
    28
    Views
    2,064

    CNMG off corners in a mill cutter?

    CNMG off corners in a mill cutter?
  14. Replies
    47
    Views
    3,877

    But, Take the spot or centerdrill just lightly...

    But,
    Take the spot or centerdrill just lightly touched and check it too.
    Maybe at 154 the chisel not the first to see metal or maybe 75% out but still on it's edge. ..:scratchchin:

    So many...
  15. Replies
    3,698
    Views
    92,462

    I can only wish this to be true but you get...

    I can only wish this to be true but you get slower. Things do not work as they once did. Balance and timing is not the same or as quick.
    Kids now..... I was this once. Sucks to be old.
    Now I go...
  16. Having dealt with many they seem complicated. I...

    Having dealt with many they seem complicated.
    I was never in the design process but have seen many fails. And then tweak, tweak, and tweak some more.
  17. Replies
    3,698
    Views
    92,462

    I cannot do that. I am 60+ years old.

    I cannot do that. I am 60+ years old.
  18. Replies
    3,698
    Views
    92,462

    Riding in a escorted parade around the town with...

    Riding in a escorted parade around the town with over 300 bikes is cool and fun no matter what you ride.
    Did this first time on my DR-350S and for sure felt out of place at the start. It was...
  19. Replies
    23
    Views
    2,614

    That is not very nice or in the spirit of do it...

    That is not very nice or in the spirit of do it yourself somehow or need it now and not buying something.
    I do not get the why of such a post and it's insults.
    Perhaps I am not a "legit" machinist...
  20. Replies
    28
    Views
    2,064

    Two inch a real design problem in an inserted...

    Two inch a real design problem in an inserted face mill. The other question being do you need a true 90 wall or just face milling.
    Ingersoll style (outboard screws) allows a higher density and body...
  21. Replies
    21
    Views
    1,570

    We used to have a Christmas party/open house when...

    We used to have a Christmas party/open house when GM and Ford allowed such.
    Every single workbench, tool box, storage cabinet, plate stand got taken out out the front building and move to the back...
  22. Replies
    41
    Views
    3,301

    In volume why does this part so scream horizontal...

    In volume why does this part so scream horizontal or 90 off and slitting type cutter on a VMC?
    I must be missing something. Often I do here.
    Laser or water? I'd drill the shit out of it before that...
  23. Replies
    22
    Views
    1,588

    Lolipop or ball nose endmill vs abrasive brush...

    Lolipop or ball nose endmill vs abrasive brush
    Guess who normally wins but a brush will not like really big burrs without affecting other things.
    Sometimes you have to look at why the program left...
  24. I find this consignment practice disgusting but...

    I find this consignment practice disgusting but do understand it to some point as no one wants to eat unused tools. The old it is in the fine print deal.
    This puts the stock and management of it...
  25. If you want one PM me. Have one barley used as I...

    If you want one PM me. Have one barley used as I convert this fixture to servo drive so that I can index for tips and reliefs on my homemade 5 axis.
    It is basically a paperweight to me. I do not...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4