Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Limy Sami

Page 1 of 60 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    19
    Views
    701

    Go to a breakers yard.

    Go to a breakers yard.
  2. Replies
    7
    Views
    513

    FYI Wicksteed Hacksaws...

    FYI Wicksteed Hacksaws

    P.S. That's a beast :D
  3. Replies
    11
    Views
    2,060

    If it all works etc etc etc, that's a pretty good...

    If it all works etc etc etc, that's a pretty good price, ............which should ?????? be recoverable on the first job - aka the sort of work only a big W&S A can do.
  4. Replies
    15
    Views
    1,968

    Any help ? Aciera F3 (Early) Manual |...

    Any help ? Aciera F3 (Early) Manual | store.lathes.co.uk

    P.S. You could contact Tony (who's a PMer) and ask if the head is in the manual ?????
  5. Replies
    33
    Views
    61,162

    Rush job - red hot urgent they said.

    Rush job - red hot urgent they said.
  6. Replies
    33
    Views
    61,162

    Same here and it's always worked for me, I'm no...

    Same here and it's always worked for me, I'm no metalagist but from what I can make out Alu and it's alloys have a critical temp for annealing, not enough and it cracks, too much and it goes ''hot...
  7. These folk say they can make any size you want. ...

    These folk say they can make any size you want. Crankshaft grinding wheels | Abtec4Abrasives
  8. The earlier ''baby Bristols'' had a Jowett flat...

    The earlier ''baby Bristols'' had a Jowett flat twin '' boxer'' engine - I think ??? from the Jowett Bradford van.

    P.S. IIRC one of the Jowett directors was also a director at Bristol.
  9. Replies
    5
    Views
    604

    As Monel k-500 work hardens like a bastard, you...

    As Monel k-500 work hardens like a bastard, you gotta be VERY careful with feeds n speeds, as in keeping the speeds low and feeds high, with ultra sharp tooling.

    PS whatever you do DON'T ream the...
  10. Replies
    9
    Views
    865

    Not when you're not only the one who has to clear...

    Not when you're not only the one who has to clear them up, suffer the financial loss of ''lost scrap'' and dig the chips out of your skin hopefully before they fester ;)

    P.S. FWIW ;- Any of the...
  11. Replies
    9
    Views
    865

    When turning, run with the tool inverted - so it...

    When turning, run with the tool inverted - so it does spray chips all over the show.
  12. Replies
    9
    Views
    1,121

    You lucky devil :D

    You lucky devil :D
  13. Replies
    9
    Views
    1,121

    UP Big Boy Vid

    #4014 ''movin out'' in August 21

    Union Pacific Big Boy #4014 Steam Train Accelerating and Sanding Flues (8/27/21) - YouTube
  14. Replies
    7
    Views
    959

    You might find it here - plenty to go through ;)...

    You might find it here - plenty to go through ;)

    American Tool Works Co. - Publication Reprints | VintageMachinery.org
  15. Replies
    17
    Views
    2,227

    I bet I'm a bigger idiot than you - so there.

    I bet I'm a bigger idiot than you - so there.
  16. Same as it does with wanking.

    Same as it does with wanking.
  17. Replies
    88
    Views
    9,782

    MMMM? The Ego has landed,...

    MMMM? The Ego has landed, ........................ I thought he'd still be far too busy single handedly saving American manufacturing from the troubles of the past years - including pre Covid.

    Or...
  18. Replies
    10
    Views
    979

    If it's Spinal Tap it's a #11

    If it's Spinal Tap it's a #11
  19. Replies
    10
    Views
    979

    I've never heard of that part of a lathe.

    I've never heard of that part of a lathe.
  20. The dozer blade would have been for snow clearing...

    The dozer blade would have been for snow clearing and similar light duties, the Ransomes MG2 (etc etc) crawler was primarily built for the market garden** trade's cultivation work.

    ** small scale...
  21. Replies
    16
    Views
    1,507

    What - 200mm dia round bar?

    What - 200mm dia round bar?
  22. Replies
    16
    Views
    1,507

    I'd use your existing saw BUT keep a NEW (as in...

    I'd use your existing saw BUT keep a NEW (as in brand spanking new aka - never used for anything other than plastic) coarse pitch blade especially for the plastic work, and run coolant.

    IME&O...
  23. Replies
    241
    Views
    16,168

    And it was very nice to see both Mr & Mrs...

    And it was very nice to see both Mr & Mrs Camscan, its a fair drive (for us Brits) from theirs to mine and to make matter worse the weather wasn't the best.

    As for the lemon drizzle cake??? heaven...
  24. Replies
    37
    Views
    2,323

    ''Suggestions on Bringing Water Into New Shop'' ...

    ''Suggestions on Bringing Water Into New Shop''

    A bucket?
  25. Replies
    25
    Views
    1,079

    OT Fuel Prices

    I don't normally brag about going to expensive places, but I've just left the gas station. :eek:
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4