Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Nicholas Bove

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    851

    I have the board that tilts down that the tubes...

    I have the board that tilts down that the tubes are on still in the machine. I need the whole plugin module box. As my machine is unfortunately missing it. I can easily rebuild the module So the...
  2. Replies
    7
    Views
    851

    Monarch 10ee module needed

    I am on the hunt for a monarch plugin tube module for my 1963 monarch. Any leads for this much needed part will be greatly appreciated!
  3. Replies
    6
    Views
    680

    Its missing the actual module that plugs in along...

    Its missing the actual module that plugs in along with one C16J and the C3J. I found a new old stock Salvania C3J off eBay last night for $38
    I'm fortunate enough that the lathe came with all the...
  4. Replies
    6
    Views
    680

    1963 Monarch 10EE parts needed!

    I just took delivery of a nice clean Monarch 10EE built in 5/63. Was told on the phone that it was a running machine. Opened it up today to find the modular drive is missing one C16J tube is missing,...
  5. Brown & Sharpe no2 surface grinder dilemma

    Hello, I got a Brown & Sharpe no2 surface grinder almost a year ago serial number 4904 that I guess I can say was in impulse buy. It was originally driven by an overhead line shaft. I started...
  6. I have seen some surface grinders with the power...

    I have seen some surface grinders with the power feed belt turned 180 degrees. On the one I have the casting does not allow the belt to go through when twisted 180 degrees. This is what it looked...
  7. Brown and Sharpe no2 surface grinder parts needed

    Hello I just got a Brown and Sharpe no2 surface grinder, serial number 4904. First of all can some one tell me what year it was made? I think it was originally belt driven off overhead works because...
  8. Hello, I just bought an old Brown & Sharpe no2...

    Hello, I just bought an old Brown & Sharpe no2 surface grinder that has an old Brown & Sharpe 6x18 magnetic chuck on it, the chuck works but the handle is very hard to pull I want to open it to clean...
  9. Replies
    9
    Views
    1,348

    Do you have any parts left? I need some of the...

    Do you have any parts left? I need some of the very unusual machine screws, my machine is serial # 4904 I also may need the lead screw and nut for the table feed.
  10. I just got a Brown & Sharpe no2 surface grinder...

    I just got a Brown & Sharpe no2 surface grinder serial number is 4904 and it still has the tapered plain bearings in it. What do people think about using Mobil Velocite Oil No. 3? Also whats the best...
  11. Replies
    22
    Views
    6,447

    I am looking into getting a 10ee round dial. I...

    I am looking into getting a 10ee round dial. I have read on this forum that they can be run with a 7.5 hp static phase converter but the lathe will surge unless started up at a low speed and then...
  12. Thanks for all the info, When i get one of these...

    Thanks for all the info, When i get one of these lathes i'll use a rotary phase converter to power it at 230 volts. theres some nice 7.5 hp rotary converters on ebay brand new made in the US backed...
  13. I have seen tandem armature MG's, but i have also...

    I have seen tandem armature MG's, but i have also seen MG's that have the 3 phase motor mounted on top of the dc generator and are connected via a belt. are those less common?
  14. I would never pull out the entire drive system, I...

    I would never pull out the entire drive system, I would want to keep it as original as possible. I just thought after looking at the mg system on the 10EE's i've seen on ebay or the ones floating...
  15. I'm looking into some day getting a 10EE round...

    I'm looking into some day getting a 10EE round dial for my shop and restore it back to new condition, i've done many restorations including my 1969 MG so i know what i would be getting into..
    I was...
Results 1 to 15 of 15