Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mark costello

Page 1 of 38 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    50
    Views
    2,416

    You are lucky They even talk to You. Where I live...

    You are lucky They even talk to You. Where I live the standard answer is NO. While trying to pay no attention to You.
  2. Replies
    1
    Views
    478

    The 5 0f #1008 are sold.

    The 5 0f #1008 are sold.
  3. Don't say that, They might take it as a challenge.

    Don't say that, They might take it as a challenge.
  4. Replies
    0
    Views
    223

    Brown and Sharp 3-4" micrometer.

    I have a Brown and Sharp 3-4" micrometer to sell in nice condition. Has shop patina. $35 buyer pays flat rate shipping.321119
  5. Replies
    1
    Views
    478

    Woodruff key seat cutters.

    I have 9-#707,.220"x1"dia.x 1/2" shaft to sell,$6 each,buyer pays shipping.
    I also have 5-#1008,320969.312"x1"dia.x 1/2" shaft to sell, $6 each, buyer pays shipping.
  6. Replies
    5
    Views
    345

    Thank You, learned something today. Are the...

    Thank You, learned something today. Are the chasers of any value or scrap? I was thinking of brazing them to a tool holder to thread OD's.
  7. Replies
    21
    Views
    1,404

    It is in a heated garage so I would not expect...

    It is in a heated garage so I would not expect more than light surface rust.
  8. Replies
    5
    Views
    345

    You know more about them than I do!

    You know more about them than I do!
  9. Replies
    5
    Views
    345

    Landis Pipe thread chasers.

    I have a set of Landis chasers for 1 1/4" pipe.$20+ flat rate shipping, will easily fir in a padded envelope.319554
  10. Replies
    21
    Views
    1,404

    Not that I am too anal about things, I use a 48"...

    Not that I am too anal about things, I use a 48" deck on a riding mower and got tired of rebuilding the shaft and rollers. So this winter I rebuilt the shaft with a piece of 4140 PH. The rollers were...
  11. Replies
    6
    Views
    650

    It is an R+L #1.319051319052

    It is an R+L #1.319051319052
  12. Replies
    6
    Views
    650

    Answers tonight.

    Answers tonight.
  13. Replies
    6
    Views
    650

    Balance turning tool

    I have a balanced turning tool to sell. It used 2 included tool bits that can be individually set for depth and diameter. It also has a 5/8"bore with an included 1/2" bushing. The drill bit not...
  14. Replies
    4
    Views
    834

    SOLD,10 letter minimum.

    SOLD,10 letter minimum.
  15. Replies
    4
    Views
    834

    Yer 2nd in line.

    Yer 2nd in line.
  16. Replies
    4
    Views
    834

    Fowler Dial Bore Gauge

    I have a used 1 time like new dial bore gauge to sell. The job got cancelled, I tried it out once. .7" to 1.50" range. Buyer pays actual shipping. 317837$75.00
  17. Replies
    18
    Views
    1,054

    What thread percentage are You using?

    What thread percentage are You using?
  18. Replies
    12
    Views
    1,064

    I am subscribed to Modern Machine Shop and They...

    I am subscribed to Modern Machine Shop and They had a coupon included with the magazine. $100 off tools with no minimum. Played My song loud and clear. Ordered $90 worth (could have cut it closer)...
  19. Replies
    56
    Views
    4,189

    Try turning the spindle from the outer end, the...

    Try turning the spindle from the outer end, the same applies when tramming a mill, turn by the pulley not the end of the quill. Chasing small dimensions means paying attention to the small details.
  20. Ground down a pair to fit in thin "O" ring...

    Ground down a pair to fit in thin "O" ring grooves.
  21. Did They find the cause?

    Did They find the cause?
  22. Replies
    178
    Views
    17,748

    Put Me down for a box also.

    Put Me down for a box also.
  23. Replies
    31
    Views
    2,731

    Could I see some pictures of the end mill...

    Could I see some pictures of the end mill sharpener, I am interested? Any collets with it?
  24. Replies
    11
    Views
    1,204

    Could be a bastard size, nothing is set in stone...

    Could be a bastard size, nothing is set in stone anymore.
  25. Ours showed up yesterday by snail mail.

    Ours showed up yesterday by snail mail.
Results 1 to 25 of 947
Page 1 of 38 1 2 3 4