Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JST

Page 1 of 60 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    19
    Views
    964

    Some Bubba with shims may hev done sonething like...

    Some Bubba with shims may hev done sonething like stuffed some under the V way contact surface "to fix the taper" while it was set on HIS crappy floor that looks like the Appalachians. Check that,...
  2. Replies
    43
    Views
    2,000

    One added idea for new graduates.... Take the...

    One added idea for new graduates.... Take the EIT, or whatever they call it now. That will allow you to later get your PE just by recommendation of a few other PEs. That is something that can end...
  3. That was the point. Induced currents is a...

    That was the point.

    Induced currents is a different matter. Normally a Faraday cage is needed to block those effects.

    The tall conductive thing is simply to avoid direct strikes on things...
  4. All sorts of things can cause low torque with a...

    All sorts of things can cause low torque with a VFD...

    First thing is a bad setting of max amps. It seems, but is not clear, that this is not the likely cause.

    However, many VFDs can be set...
  5. Replies
    18
    Views
    429

    First take a look at the box for the cubic...

    First take a look at the box for the cubic capacity, then check the volume per wire. You have no strap-mounted devices, so that is not an issue.

    it is 2.25 cubic inches per wire for 12 ga, I...
  6. Along with that "protected zone".... The rule I...

    Along with that "protected zone".... The rule I have been given is to go from the top of the tallest conductive item, down at an angle. Some say 30 deg from horizontal, some say 45 deg, and a few...
  7. You need to find out what is being contemplated...

    You need to find out what is being contemplated there. 8k might be reasonable, depending on the house.... 2k SF can be done several ways. Some have more needs-to-be-protected area than others.
    ...
  8. Assuming it is a gas truck, not diesel....... ...

    Assuming it is a gas truck, not diesel.......

    Gas sitting in the truck for 2 years is bad. It probably does not (as mentioned) even smell like gas. It will barely burn. That's enough problem...
  9. Maker likely expected the load motor would have...

    Maker likely expected the load motor would have its own contactor in the machine, which accounts for no output contactor. That is pretty much how it would be if the machine/motor were wired to a 3...
  10. Replies
    6
    Views
    572

    Yeah, that was another item on the list. It just...

    Yeah, that was another item on the list. It just keeps going... there is way more missing than is left. Makes a person wonder about all the hidden things that do not show in the photos.

    If you...
  11. Replies
    6
    Views
    572

    Not an issue... the seller is the clueless (or...

    Not an issue... the seller is the clueless (or greedy) person in this.

    Those 1020s seem like a very nice machine comparable to a 10EE.... Much more generally useful than the 608, which is a...
  12. Replies
    6
    Views
    572

    There is so little left of it that it is really a...

    There is so little left of it that it is really a parts machine in many ways. The entire change gear setup is missing, the tool holder is totally wrong. The headstock appears to be set up for...
  13. While this is probably good advice, not knowing...

    While this is probably good advice, not knowing details, the braking is not more violent than acceleration, I have tested similar sized machines and was unable to get a 6" or a 5: chuck to...
  14. I have a few, I get 'em for a couple bucks at...

    I have a few, I get 'em for a couple bucks at estate sales. Dirty ones go for cheap. Nice shiny ones cost money. All of them work the same, and there are rags and water everywhere.....
  15. If all you have is a 4 way transformer, going in...

    If all you have is a 4 way transformer, going in with 115 on the 480 winding, coming out the 240 and leaving that for 30 min or so, then 115 into 240:240 winding, leaving that for 30 min or so, then...
  16. Replies
    13
    Views
    568

    1", eh? That's more than I have. As far as I...

    1", eh? That's more than I have. As far as I know that (my) machine has a 10" saddle etc, but they are so close that they probably interchange. I have a t-slot crosslide from an 11", and it fits...
  17. It may not turn on. When testing those, I have...

    It may not turn on. When testing those, I have always used a "4 way" transformer, 120/240 to 240/480. other than that, no damage from a basic test of turn on and run. Some can refuse to work if...
  18. Replies
    13
    Views
    568

    What's your distance from compound to spindle...

    What's your distance from compound to spindle center? Some may be larger, my 200 is smaller than most in that dimension.
  19. Replies
    6
    Views
    540

    That thing really does look very well made and is...

    That thing really does look very well made and is quite "pretty". Seems too small for practical use, might it be some sort of sample piece or the like?
  20. Replies
    13
    Views
    568

    Maybe not so fast.... The 200 is really too...

    Maybe not so fast....

    The 200 is really too small for the toolposts. Yes a 10" is big enough, but the distance from compound to spindle center is tiny, like 0.875". iI's marginal on clearance...
  21. "fuse paper"? Good one... had not heard that...

    "fuse paper"? Good one... had not heard that one before.

    Not recommended, of course........
  22. Replies
    36
    Views
    1,811

    it was pretty expensive at one time for balloons...

    it was pretty expensive at one time for balloons and Zeppelins, when it was a product of zinc and acid.... So, in essence, probably yes.

    The real intent is to make "cars" rare and very expensive....
  23. Replies
    36
    Views
    1,811

    The serious problem with hydrogen or any other...

    The serious problem with hydrogen or any other such fuel that must be "created" by some process that itself takes energy, is that it cannot compete.

    When there iis fuel that you can basically...
  24. Replies
    18
    Views
    1,308

    Since you are not afraid (obviously) of some...

    Since you are not afraid (obviously) of some work, you can MAKE the damn arbor in a day from a chunk of 4140 (for the classy job) or even just regular 1018. Spacers are available new from sources...
  25. Replies
    22
    Views
    10,104

    Split rivets are available from McMaster. I do...

    Split rivets are available from McMaster. I do not know if they are available nickel plated, though. But when the steel parts are re-nickel plated, the rivets can be also maybe.

    The...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4