Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: packardbill

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    1,309

    Chris, I have several serpentine belts (good...

    Chris, I have several serpentine belts (good used). If you're interested, I'll send you one for the cost of shipping (USPS). Just let me know what width and length, and maybe I'll have something...
  2. Replies
    13
    Views
    1,245

    If your 14.5" has a spindle thread of...

    If your 14.5" has a spindle thread of 2-3/8"x6tpi, you will need a South bend 5c adapter. The adapters from a 10L (large spindle 10"), a 13" with 2-1/4"x8tpi (early ones had a 1-7/8" threaded...
  3. Replies
    5
    Views
    506

    CXA on my 16. Fits! PB

    CXA on my 16. Fits! PB
  4. Replies
    3
    Views
    393

    PM sent, Thanks, PB

    PM sent, Thanks, PB
  5. Replies
    8
    Views
    691

    Contact southbendlatheman (a member here) to see...

    Contact southbendlatheman (a member here) to see if he has any for sale, or Brian Miller (another member) at millermachineandfabrication.com He made a small run a while ago and may have a set for...
  6. Replies
    15
    Views
    1,151

    Wishing you the best Jim, and thanks for the past...

    Wishing you the best Jim, and thanks for the past excellent service with the plates. PB
  7. Hi Verl, you could go to Roton.com or...

    Hi Verl, you could go to Roton.com or nookindustries.com and buy a length of screw and turn the ends and thread on your lathe, and then take it to a machine shop with the capability to cut the...
  8. Replies
    10
    Views
    1,187

    Gregory,you're welcome. If you go to wswells.com...

    Gregory,you're welcome. If you go to wswells.com you will find a wealth of knowledge about south bend lathes. If you scroll down that page and click on the square at the lower left of the page (south...
  9. Replies
    10
    Views
    1,187

    1948 10l. Pb

    1948 10l. Pb
  10. Replies
    36
    Views
    1,962

    In your first post you ask about the plate...

    In your first post you ask about the plate mounted to the bed under where the tailstock is clamped in your picture. It is a "South Bend Lathe" name plate that was used before the "10" south bend",...
  11. Replies
    12
    Views
    1,007

    Weren't the 123's a "change gear" lathe? The...

    Weren't the 123's a "change gear" lathe? The 117's were quick change. OP's lathe has early 2 TPI quick change box on it. But, it might be a custom job for Herbert. PB
  12. Replies
    2
    Views
    422

    '52 10L..10" swing, Large bore (1.375") spindle ....

    '52 10L..10" swing, Large bore (1.375") spindle . The eleven has something to do with production upgrades. PB
  13. Replies
    2,358
    Views
    460,673

    Sticky: Workshop model B, although I thought modelB was...

    Workshop model B, although I thought modelB was introduced in 1939.Maybe Mr. Wells can offer more info on this.

    Horizontal, Plain (no belt adjustment) motor drive.

    Good luck with your lathe. PB
  14. The bearing is on the side that takes the thrust...

    The bearing is on the side that takes the thrust from the tailstock pressure and the cutting forces from the tool when cutting towards the headstock or facing. Make sense? PB
  15. Hi Shay. If your lift has a Impco/Nolfs model J...

    Hi Shay. If your lift has a Impco/Nolfs model J converter/regulator, it will have two fittings for engine coolant.
    The model J was probably the most common converter for 4 cylinder propane lift...
  16. Replies
    6
    Views
    695

    Your headstock has segmented iron bearings...they...

    Your headstock has segmented iron bearings...they are not interchangeable. Your bearings do NOT look bad. The minor scoring looks negligible. Clean the bearing surfaces with a nylon or bronze brush...
  17. Dirt, I don't notice a spindle adapter for the...

    Dirt, I don't notice a spindle adapter for the collets or a thread protector. You'll need both of those to make use of the collets. If I can make a suggestion, save your money on the motor...
  18. Replies
    13
    Views
    1,718

    Check the motor tag. Will tell manufacturer...

    Check the motor tag. Will tell manufacturer (Westinghouse,Louis Allis,Century, etc.),Horsepower,Phase(single or 3)and voltage(220/440) and single or two speed. I doubt someone would have put a 120...
  19. Replies
    16
    Views
    1,641

    Definitely scour the forklift dealer/repair shops...

    Definitely scour the forklift dealer/repair shops for a used setup. A new Cascade positioner cylinder is about 2K new, and you may need a false carriage to mount it to your machine carriage. Best to...
  20. You can transition from the cast hub to schedule...

    You can transition from the cast hub to schedule 40 by removing the 90*sweep and cleaning the hub and place your schedule 40 into the hub and pack with oakum and seal with Hercules plastiseal (if I...
  21. Replies
    8
    Views
    975

    Probably this model:...

    Probably this model: http://vintagemachinery.org/photoindex/images/16303-A.jpg PB
  22. Replies
    8
    Views
    975

    Old style as mentioned and for shorter beds.PB

    Old style as mentioned and for shorter beds.PB
  23. Replies
    67
    Views
    4,972

    Husqvarna has made the smaller line of JD lawn...

    Husqvarna has made the smaller line of JD lawn tractors for quite some time. I know that Husqvarna has a upgraded tractor with a 54" deck that can only be bought at a husq dealer. Not big box stores....
  24. Replies
    13
    Views
    1,220

    It is a 10L (heavy ten)...CL 187AB..a four footer...

    It is a 10L (heavy ten)...CL 187AB..a four footer with wide range gearbox. I do not see, and it probably does not have, a taper attachment, but not a problem unless you need one. It does have a...
  25. With the large spindle and oversized motor, you...

    With the large spindle and oversized motor, you should have no problem stuffing a 1.250" barrel blank through the spindle and turning it, but does the lathe come with a steady rest and follow rest to...
Results 1 to 25 of 333
Page 1 of 14 1 2 3 4