Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: acme thread

Page 1 of 45 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    51
    Views
    6,547

    My first reaction to the original post,Was that...

    My first reaction to the original post,Was that sounds pretty cheap for the level. After reading the follow up mess, I'm thinking someone offered him more money for it,
    I have been contacted through...
  2. Replies
    5
    Views
    884

    Akajun, I've got a pair of .338 Win. Mag.reground...

    Akajun, I've got a pair of .338 Win. Mag.reground reamers; rough/finish. They haven't been used since regrind,So I can't guarantee anything. You can have them for postage, both have live pilots.
    Pm...
  3. Replies
    6
    Views
    800

    Just get a room already. :D dave [acme thread]

    Just get a room already. :D dave [acme thread]
  4. Spud, I owned a 2004 Duramax/Allison,and wanted...

    Spud, I owned a 2004 Duramax/Allison,and wanted to put a winch on it,Took it to Custom Clutch in Cleveland for an estimate. When they pulled the rectangular plate on the transmission,They showed me...
  5. Just because you have a Duramax /Allison 3500,...

    Just because you have a Duramax /Allison 3500, Doesn't mean you have a gear in your transmission for a PTO. My 2013 Dura/Allison WORK TRUCK shows a optional PTO on my bill of sale, Pull the cover...
  6. Just to throw more crappola into the game, I've...

    Just to throw more crappola into the game, I've got an old Lufkin 50FT. tape; That's marked up to 600 inches.
    But, marked "consecutive inches in tenths" . The graduations between the inch marks are...
  7. Replies
    10
    Views
    884

    I would shift the worm out of engagement before...

    I would shift the worm out of engagement before you start beating and banging on it, You don't want to ding the ring gear with the worm gear. My center is just a short 3 or 4 Morse taper, Should...
  8. Replies
    7
    Views
    1,013

    Cut off tools no longer available. Dave...

    Cut off tools no longer available. Dave [acmethread]
  9. Replies
    7
    Views
    1,013

    These are pretty much the Holy Grail with the...

    These are pretty much the Holy Grail with the Hardinge crowd, I sure didn't pay that much for them, I've probably been tripping over them for 20 yrs. These are T shaped blades,So you need some...
  10. Replies
    7
    Views
    1,013

    Yes they are, I tried to post a picture, But came...

    Yes they are, I tried to post a picture, But came to realize that the software designers here must be ex politicians. The original post was 30 billion cubits too large or something of that nature....
  11. Replies
    7
    Views
    1,013

    F/S Somma,NOS. micrograin cut off tools

    6- 3/32" x 11/16"x 5" P3N
    2- 5/32" x 11/16" x 5" P5S
    NOS. in SOMMA paper wrappers, ends are plastic dipped.
    Double ended ,micrograin carbide. Will all fit a small flat rate. all for one...
  12. I also have a 2013 ,3500 4x4 with the Duramax...

    I also have a 2013 ,3500 4x4 with the Duramax /Allison package. I just got it out of the dealer's last fall ,With a leaky headgasket. It filled up the cylinder with coolant,and was pulling 750 amps...
  13. Replies
    13
    Views
    1,037

    I think your nuts,To even consider putting...

    I think your nuts,To even consider putting 750lbs. of iron in the back of a Suburban, There's no way to tie it down. If you get in an accident, That bunch of iron is going through your windshield. I...
  14. Replies
    49
    Views
    5,718

    You'll just have to hold it.,Till the Hillary...

    You'll just have to hold it.,Till the Hillary campaign pictures and posters come out. Dave [acme thread
  15. Replies
    12
    Views
    1,211

    You need some edumbjucation yerself Should be...

    You need some edumbjucation yerself Should be DON"T KNOW'
    No capitalization,no punctuation, and you have the gall to call people uneducated. You don't seem to have a grasp of spell checker...
  16. Replies
    12
    Views
    1,211

    Tootie, Lets move it over to a PM. dave [acme...

    Tootie, Lets move it over to a PM. dave [acme thread]
  17. Replies
    34
    Views
    2,092

    Farriers, [The guys who shoe horses] will uses...

    Farriers, [The guys who shoe horses] will uses BORIUM rods. Hollow bronze tubes filled with flux and crushed carbide, To braze onto horse shoes on buggy horses and work horses for winter rd.traction....
  18. Replies
    12
    Views
    1,211

    I've got two of them,24 slot,.492" thick 6.740"...

    I've got two of them,24 slot,.492" thick 6.740" Dia.3.250" center hole. used ,$35.00 each + shipping
    Masking plate set 12-8-6-4-3-2 used $65.00 each+shipping have 2 sets
    misc. masking plates ...
  19. Replies
    1
    Views
    426

    I've repaired several chuck sockets split like...

    I've repaired several chuck sockets split like that,By boring out the socket,and silver soldering the top of a Allen head cap screw into the hole, It helps to take a skin cut
    off the OD of the cap...
  20. Collets spoken for, Merry Christmas everyone! ...

    Collets spoken for, Merry Christmas everyone! Dave [acme thread]
  21. Free for Christmas,Deckel grinder colets

    Free for Christmas , 13 Deckle [type] collets,not marked Deckel.243996
    dave [acme thread], using shape,not pristine, will fit a small flat rate box.
    4.838"long, .786 body dia..771 od. of Buttress...
  22. Replies
    14
    Views
    1,471

    Wow! 3 inquiries for this junk, It will depend on...

    Wow! 3 inquiries for this junk, It will depend on the OP if he wants them,then I'll go down the list by time arrival. dave [acme thread]
  23. Replies
    14
    Views
    1,471

    I've got some parts for that sucker, I've got...

    I've got some parts for that sucker, I've got everything you have shown ,with the exception of
    the clamp dog and driver, I believe the cast iron base has broken T-slot. I have the 30-36
    and 28-48...
  24. Replies
    3
    Views
    4,150

    It looks like it could be real handy;If that...

    It looks like it could be real handy;If that vertical head can really weld. But it looks like you have to upset the mill to weld vertical. dave [acme thread]
  25. Your picture 3/of/3 shows the lack of a front...

    Your picture 3/of/3 shows the lack of a front seal, The original seal must have been trashed when they welded on the end of the input shaft. That's [the lack of the seal] is why the pumps probably...
Results 1 to 25 of 1111
Page 1 of 45 1 2 3 4