Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sudsy55

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Are you getting any errors or does it just...

    Are you getting any errors or does it just unclamp and sit there? If just sitting there you need to check if its getting the index signal. Should be able to see this on the ladder
  2. How did you go? Get it sorted?

    How did you go? Get it sorted?
  3. Replies
    16
    Views
    844

    Might pay to flip the breakers off then back on....

    Might pay to flip the breakers off then back on. Some types of breakers can look like they are on but have actually tripped
  4. Replies
    16
    Views
    1,320

    Actually I think there is an epprom you will need...

    Actually I think there is an epprom you will need but after that the other options may be just parameter related. It is on the memory modules (lower left side of controller. I can't remember the...
  5. Replies
    16
    Views
    1,320

    Knowing what they're like there is probably...

    Knowing what they're like there is probably another secret code you need to get into it. Try rubbing your belly clockwise, your head ccw while standing on one leg on a bungy cord in the middle of the...
  6. Replies
    16
    Views
    1,320

    Interesting to see the outcome

    Interesting to see the outcome
  7. Replies
    4
    Views
    615

    And I do that how exactly???

    And I do that how exactly???
  8. Replies
    4
    Views
    615

    I have tried all different combinations. Changed...

    I have tried all different combinations. Changed a couple of parameters associated to chamfering and still the same
  9. Press MNT PressPLC PressPREG Pressthe clear...

    Press MNT
    PressPLC
    PressPREG
    Pressthe clear key once (top rh corner} (this puts the keypad in letter mode)
    Press 6 9That should give you ( R) in the brackets at the bottom
    Punch in 2390 (this...
  10. You press the management button then go to PLC I...

    You press the management button then go to PLC I think. Will check tomorrow
  11. Change it with machine running is the best but...

    Change it with machine running is the best but can be done with machine off if you get it done in short time
  12. These are the parameters on my H400 so I don't...

    These are the parameters on my H400 so I don't know if yours would be the same but being M32 I would say they should be the ones.R2390is the distance between the switch signals. You will have to...
  13. Replies
    4
    Views
    615

    Doing my head in

    G'day all,
    have just recently started working my H400 with M32 controller. I'm having trouble getting the chamfer program to work. Have tried different size tools and adjusted a couple of...
  14. Its done in the R parameters. Not in the shed at...

    Its done in the R parameters. Not in the shed at the moment so not sure which one offhand. Takes a little bit of mucking around and measuring but not too difficult
  15. Thread: M32 FLD Error

    by sudsy55
    Replies
    3
    Views
    458

    Will usually only boot from disc if battery is...

    Will usually only boot from disc if battery is going flat. There is a battery in the module beside the FDD as well as the big 6v battery and another on one of the boards(can't remember which one...
  16. Replies
    13
    Views
    730

    Not sure if the M plus is similar to M32 but if...

    Not sure if the M plus is similar to M32 but if when you are writing the block you have the options on the bottom. If you select other it will bring up more options with index being one of them. Like...
  17. Replies
    13
    Views
    730

    Why have you got the centre drill as a manual...

    Why have you got the centre drill as a manual program? In the Mazatrol tapping cycle you have the centre drill, tapping drill and tap in the one cycle.
  18. When you write your program I usually make my...

    When you write your program I usually make my first unit the WPC. That's where you put your job zero co-ordinates. The machine now knows where your workpiece is. Its like zeroing your part in the...
  19. Thread: H400 3d

    by sudsy55
    Replies
    0
    Views
    336

    H400 3d

    G'day all,
    does anyone have a H400 with the 3d option? After a copy of the O parameters.

    Cheers
  20. Replies
    13
    Views
    730

    Can't you rotate the axis in Mazatrol?? I'm not...

    Can't you rotate the axis in Mazatrol?? I'm not familiar with that control and haven't done 4th axis work yet
  21. Replies
    13
    Views
    730

    I don't know if this would work for what you are...

    I don't know if this would work for what you are wanting to do but worth a try. Use the priority numbers in the mazatrol program. Number each tool in the order that you want them to do work. Like I...
  22. Replies
    16
    Views
    1,320

    I copied the opton parameters for my lathe. Not...

    I copied the opton parameters for my lathe. Not sure if it has EIA as I haven't got it powered up but will get them to you to compare with yours.
  23. Replies
    16
    Views
    1,320

    Not bad money for changing a few numbers

    Not bad money for changing a few numbers
  24. Replies
    11
    Views
    1,030

    The motors are fairly easy to get at. Just take...

    The motors are fairly easy to get at. Just take the covers off the back and you can see the motors and the belt
  25. Replies
    16
    Views
    1,320

    I may be totally wrong here but I was doing some...

    I may be totally wrong here but I was doing some reading about options on my M32 and to me it looked like if you had a certain board with some options installed (can't remember which one offhand) the...
Results 1 to 25 of 410
Page 1 of 17 1 2 3 4