Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: HOMESTEAD

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    963

    Carlton is often touted as "the best" American...

    Carlton is often touted as "the best" American made radial drill. However, I don't think you can go wrong with any of the big name players that made radials: American, Fosdick, Cincinnati Bickford,...
  2. Replies
    62
    Views
    4,287

    Scroll down to #19 in the terms and conditions...

    Scroll down to #19 in the terms and conditions for that auction. The auction co. is going to require you to have insurance to do any kind of rigging. It doesn't look like you have to use the rigger...
  3. Replies
    8
    Views
    1,016

    I keep getting one that says I've been selected...

    I keep getting one that says I've been selected by Verizon as the winner of a drawing or something. Almost always happens when I'm in the machines for sale forum. Happens just about every time I...
  4. Replies
    8
    Views
    958

    Use a hammer and punch. Place the punch against...

    Use a hammer and punch. Place the punch against the side of the nut, as close to the corner as possible, and give it a whack. Or, go to harbor freight, buy a 15/16" socket, and grind it down until...
  5. Thanks for all the help guys

    Thanks for all the help guys
  6. What kind of pump did you use? I was thinking...

    What kind of pump did you use? I was thinking along the same lines. A container of solvent, a pump, a filter to run the solvent through, and some adapters to run it through the hoses.
  7. "Make offer"

    "Make offer"
  8. Machine in question is a mid 2000's Deere 332...

    Machine in question is a mid 2000's Deere 332 skid loader. Wheel motor failed and owner is selling it as is. Sounds like one of the bearings failed. Shavings were found in the hydraulic filter. I...
  9. OT- Cleaning hydraulic system after major component failure

    What is the general procedure used to clean the hydraulic system on a piece of heavy equipment (dozer, excavator, etc.) after a component failure? Like a pump or motor failure that is suspected of...
  10. No need to worry, the idler will spin in the same...

    No need to worry, the idler will spin in the same direction as the pony motor once single phase power is supplied to it.
  11. Replies
    23
    Views
    3,715

    Would you pay anywhere near 2 grand for it though?

    Would you pay anywhere near 2 grand for it though?
  12. Replies
    23
    Views
    3,715

    Here's one I've been laughing at for a while: 24"...

    Here's one I've been laughing at for a while: 24" Prentice Sliding Head Drill Press - tools - by owner - sale. Been on craigs for months. Started out at like $2500 or so. Advertised it as "Priced...
  13. Replies
    35
    Views
    5,298

    You forgot the phrase "only surface rust," too...

    You forgot the phrase "only surface rust," too...
  14. Replies
    6
    Views
    1,048

    Gauge is spoken for, thanks guys.

    Gauge is spoken for, thanks guys.
  15. Replies
    6
    Views
    1,048

    Free: Cadillac Pla-Chek Height Gauge

    Cadillac 2500 height gauge. Got this from an auction a number of years ago because I thought it looked cool, didn't even know it's purpose at the time. The dial won't turn however. I think the...
  16. Replies
    1
    Views
    799

    All say "Beaver Mono-Type Die Head" 248331...

    All say "Beaver Mono-Type Die Head"

    248331 248332
  17. Replies
    1
    Views
    799

    FS: Beaver Pipe Threader Dies

    I have seven Beaver model A pipe threader die holders/dies. Sizes are as follows:

    3/8" NPT
    1" NPT
    1 1/4" NPT
    1/2" UNC (2)
    5/8" UNC
    1" UNC

    The threading dies themselves look to be in...
  18. Replies
    25
    Views
    1,861

    I think it's very unlikely that anybody else is...

    I think it's very unlikely that anybody else is going to give the seller $700 for a WWII vintage shaper that weighs upwards of three tons, especially when he has no way to load it. I don't care how...
  19. Yeah, if you can handle working on auto trannies...

    Yeah, if you can handle working on auto trannies and injection pumps, then you won't have any problem working on hydraulic piston pumps. As Kid said, there's not much in there. Just a swash plate...
  20. That seems to be the case, thank you for clearing...

    That seems to be the case, thank you for clearing that up.
  21. That makes sense. Must just be the valves...

    That makes sense. Must just be the valves controlling direction of flow.
  22. Pumps like this. I'm assuming they use a small...

    Pumps like this. I'm assuming they use a small gear pump.

    238121
  23. OT...Single vs. double acting 12 volt hydraulic pumps

    A few questions about single vs. double acting 12 volt hydraulic pumps guys. I have quite a bit of hydraulic experience, but I've never worked with these 12 volt pumps before.

    It looks like the...
  24. I think dealing with dealers of anything is a...

    I think dealing with dealers of anything is a major pain if you're buying used. I'm sure there's exceptions, but all I see is ridiculously over priced junk, even factoring in the haggle factor. I'd...
  25. Replies
    20
    Views
    2,768

    Haha! I see what you did there :). Whoops, I see...

    Haha! I see what you did there :). Whoops, I see Booze beat me too it...
Results 1 to 25 of 184
Page 1 of 8 1 2 3 4