Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: fmari --MariTool-

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. I've had the same problem too for a while. Still...

    I've had the same problem too for a while. Still do.
  2. Replies
    32
    Views
    1,700

    Are they balanced? :-)

    Are they balanced? :-)
  3. The Toyoda canned cycles or Studer grind software...

    The Toyoda canned cycles or Studer grind software just take way way too long. We tried to make it work but isnt for us. It is great software ( both Toyoda and Studer) but not for our application. We...
  4. Replies
    32
    Views
    1,700

    In all seriousness I tip my hat to them. It is a...

    In all seriousness I tip my hat to them. It is a great start and can lead to some pretty cool possibilities. How about using this in a drilling application? Maybe it can be so sensitive that it...
  5. Replies
    32
    Views
    1,700

    haha, april 1st 2020.

    haha, april 1st 2020.
  6. I would think all high volume applications has a...

    I would think all high volume applications has a lot of manual programming. If not you are leaving some money on the table. Some things just need manual programming to be 100% efficient. From...
  7. Replies
    32
    Views
    1,700

    Looks great. But needs to be much shorter. Best...

    Looks great. But needs to be much shorter. Best is something not part of the tool holder. Nobody want to replace an expensive "smart tool holder" if an endmill spins inside and damages the holder.
    ...
  8. Too bad you are in Sweden ( but we do ship...

    Too bad you are in Sweden ( but we do ship worldwide)

    This should work perfectly...

    Solid Carbide G3 Series Drill .1693 diameter X .945 Flute Length TiAlCN MariTool

    to start out..
    140-180...
  9. Between heat treating and other processes these...

    Between heat treating and other processes these retention knobs are going to be very durable. I have been communicating with my heat treaters metallurgist several times and he has been a great source...
  10. I think if every crash or failure was the same...

    I think if every crash or failure was the same that question can be answered. But that is not the case. I would imagine if a crash had a large rotational force as part of the total forces the coolant...
  11. That gear like any gear can be easily balanced...

    That gear like any gear can be easily balanced and will remain perfectly balanced for the life of the spindle as long as a tooth doesnt chip or it gets damaged. But that gear is a decent sized gear...
  12. Bulk of the time was getting the material. I...

    Bulk of the time was getting the material. I order directly (still thru Dist but material goes directly from mill to my floor) from the mill so I get good pricing. But that also means 40,000 lbs min...
  13. Replies
    29
    Views
    2,167

    5" od solid carbide slitting saws are now in...

    5" od solid carbide slitting saws are now in stock. Tialn coated and staggered tooth. From .0469-.140 widths...

    Solid Carbide Circular Sawblades - MariTool
  14. All of our retention knobs have a pilot dia. That...

    All of our retention knobs have a pilot dia. That is not protected. Price will remain the same as our current retention knob $14.62. It will look identical to how it is now. Not much we can change....
  15. Ok guys. Sorry for the delay. Kids had some...

    Ok guys. Sorry for the delay. Kids had some soccers tournaments this weekend so I was very busy. I read all the posts and I am up to speed. Here are a few points...

    I'm not going to be an...
  16. " When I called Maritool before ordering about...

    " When I called Maritool before ordering about $1500 worth of ER-20 and ER-32 holders, pulls studs and a face mill holder I asked the person about what studs were needed and was told that the...
  17. The way those ball detents are so deep it really...

    The way those ball detents are so deep it really looks the the retention knob held on for dear life!! Some ball witness marks are perfectly normal. Those marks are very deep.
  18. Mickey_D, I spoke to you. I certainly did not...

    Mickey_D,

    I spoke to you. I certainly did not just say ya they can break. I asked you about the application and I also mentioned they we sell high strength retention knobs that are much stronger...
  19. Replies
    15
    Views
    970

    If you really want to split hairs Mazak has a...

    If you really want to split hairs Mazak has a valid point. Every spindle will have a different wear pattern over time. It will mirror that pattern on the tool holder ( the holder is softer). Put the...
  20. Adam, I love your shop and how it is so clean...

    Adam,

    I love your shop and how it is so clean and organized. The surface finishes that Mori leaves is unreal. I just checked my tool holder balancers and too bad I dont have a adapter for HSK32 or...
  21. Replies
    21
    Views
    1,203

    I sent you a DM. Thank you.

    I sent you a DM. Thank you.
  22. Replies
    21
    Views
    1,203

    as9100d, thank you for the kind words. ...

    as9100d,
    thank you for the kind words.

    empwoer,
    I look forward to working with you.

    Yes from time to time we offer tooling certificates. We try to avoid it. generally this is how it goes....
  23. Replies
    8
    Views
    551

    700-1000 sfpm ? really? Im 403 stainless I would...

    700-1000 sfpm ? really? Im 403 stainless I would love to see a video of that....
  24. Oldwrench, Thank you sir. We do our best.

    Oldwrench,
    Thank you sir. We do our best.
  25. Replies
    26
    Views
    2,232

    Wow, we are polar opposite. But so far I didn't...

    Wow, we are polar opposite. But so far I didn't have to really buy any parts for this machine so maybe my opinion will change. I am used to decoding manuals. Ever read a Fanuc manual in the late...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4