Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: enginebill

Page 1 of 48 1 2 3 4

Search: Search took 0.02 seconds.

  1. You can safely braze the crack. It is an...

    You can safely braze the crack. It is an unconstrained crack and it will not crack again.
  2. Replies
    4
    Views
    431

    If you send measurements and the missing numbers,...

    If you send measurements and the missing numbers, Rob Gill can make you a new tag, [email protected] . Expect to pay around $150 for the tag.
  3. Can you post a video of the operation? It doesn't...

    Can you post a video of the operation? It doesn't look like the belt wants to move at all. The countershaft belt on my Putnam planer is only about 4' from the line shaft and those tight and loose...
  4. John, That is a nice looking planer. The belt...

    John, That is a nice looking planer. The belt shifter needs to be on the leading side belt. In your photo the belt should be running down, the belt should be good and tight too. And obviously the...
  5. Replies
    9
    Views
    1,044

    I have a 16 pole 3 phase motor with a 435 full...

    I have a 16 pole 3 phase motor with a 435 full load rpm but it is only 3/4 HP, it is the size of a modern 10 HP motor though.
  6. Replies
    2
    Views
    388

    It sounds like this is your first lathe. The...

    It sounds like this is your first lathe. The spindle inside diameter at the chuck end is tapered for a dead center and is probably 4, 4 1/2 or 5 Morse taper. You say it turns something out of round,...
  7. Replies
    22
    Views
    30,010

    Sticky: The last I heard was that some stuff was scrapped...

    The last I heard was that some stuff was scrapped by the person that Chad sold the building to. Also the city is working towards taking the whole property over.
  8. Replies
    71
    Views
    6,088

    Dave, I think there would be three hubs on the...

    Dave, I think there would be three hubs on the wheel shaft. The two hubs on the left are the inside and outside of the outside hubs, two per wheel. The hubs on the right are the inside and outside of...
  9. Replies
    30
    Views
    2,113

    Couldn't you use an impulse from another magneto?

    Couldn't you use an impulse from another magneto?
  10. Here is a web site where you can sell the gas...

    Here is a web site where you can sell the gas engines, Medium Flywheel Engines and Parts For Sale
    Here is one for steam engines, Steam and Traction Engines For Sale
    The machinery can be sold...
  11. Replies
    71
    Views
    6,088

    What I see there is a copper bowl since the...

    What I see there is a copper bowl since the boiler is copper the copper circle would have to be bowl shaped for the pressure. The strap is on the bottom, the copper bowl is just above the strap and...
  12. Replies
    71
    Views
    6,088

    Send me your email address in a private message...

    Send me your email address in a private message by clicking on my name and I will forward it to him.
  13. Replies
    71
    Views
    6,088

    Have you talked to Alex Karnes? He is a young kid...

    Have you talked to Alex Karnes? He is a young kid but is very knowledgeable about steam.
  14. Replies
    71
    Views
    6,088

    You will figure it out eventually.

    You will figure it out eventually.
  15. Replies
    71
    Views
    6,088

    I think that you would not need a slip joint on...

    I think that you would not need a slip joint on the condenser with a piped connection as the pipe would just move away from the condenser freely. The slip joint would have to be in the center of the...
  16. It looks more like rust pitting but it would be...

    It looks more like rust pitting but it would be nothing I would worry about.
  17. Replies
    25
    Views
    4,548

    Why not use the original motor and use a...

    Why not use the original motor and use a transformer to make 440V?
  18. Replies
    11
    Views
    1,232

    It could be an Aerolux light bulb for decoration....

    It could be an Aerolux light bulb for decoration. My wife has three that I made a stand for an they light up.
  19. Replies
    25
    Views
    2,102

    Try searching trademark images for moon or arrow.

    Try searching trademark images for moon or arrow.
  20. Replies
    24
    Views
    1,981

    That is the stupidest thing that I have ever...

    That is the stupidest thing that I have ever heard.
  21. Replies
    24
    Views
    1,981

    All of the regulars should know this by know, new...

    All of the regulars should know this by know, new members who don't specify their location on their profile get the first on the list, Aland Islands. It is a flaw on the forum.
  22. Replies
    15
    Views
    956

    If that is what you measured, then that is what...

    If that is what you measured, then that is what it is. There was no standard so lathe manufacturers could make what ever they wanted. You are not likely to find a ready made back plate, you have to...
  23. Replies
    8
    Views
    671

    The threads can be a little loose and it wont...

    The threads can be a little loose and it wont hurt anything. The register on the spindle gives you the center and the shoulder on the spindle keeps the chuck square.
  24. Replies
    8
    Views
    671

    If you have a chuck that fits the spindle now,...

    If you have a chuck that fits the spindle now, just chuck up the new back plate and pick up the treads and open them up some. After you take a pass or two, unscrew the old chuck with the new plate...
  25. Replies
    11
    Views
    1,292

    Your photo shows a surface plate.

    Your photo shows a surface plate.
Results 1 to 25 of 1179
Page 1 of 48 1 2 3 4