Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Rick Finsta

Page 1 of 23 1 2 3 4

Search: Search took 0.01 seconds; generated 9 minute(s) ago.

  1. Replies
    63
    Views
    4,183

    Well I must have miscalculated because I get low...

    Well I must have miscalculated because I get low noise (basically the noise from the line only) but only 0.6V out the back side of my shunt. Back to the drawing board...
  2. You need to call the tool radius compensation...

    You need to call the tool radius compensation type for the tool nose position; the FANUC manuals for your controller specify these.

    EDIT: So you know, this is what the "T" column in your tool...
  3. Replies
    63
    Views
    4,183

    Are they saying as long as the ripple voltage is...

    Are they saying as long as the ripple voltage is within that 4.8V range you're fine? LOL
  4. Replies
    63
    Views
    4,183

    Exactly! If I buy another machine I don't think...

    Exactly! If I buy another machine I don't think it is going to be entry-level.

    So it'll only cost me $32 to get a replacement power supply off Amazon from the OE supplier, however they do only...
  5. Replies
    63
    Views
    4,183

    Okay I scoped both the 24V and 24P referencing...

    Okay I scoped both the 24V and 24P referencing the 0V and 0L and both were very similar. I have something like 20-35mV RMS but if I measure Vpp I am getting a few hundred mV. Then, when I engage...
  6. Replies
    63
    Views
    4,183

    Yeah... I'm thinking if I ever buy anything FANUC...

    Yeah... I'm thinking if I ever buy anything FANUC again it is going to be of the 31i or 32i variety.

    I hate to say it but I may end up with a Robodrill after I repair this machine. I want a...
  7. Replies
    63
    Views
    4,183

    Thing is, it is 63 pages long!

    Thing is, it is 63 pages long!
  8. Replies
    63
    Views
    4,183

    Does anyone have a good way to host a .PDF? I...

    Does anyone have a good way to host a .PDF? I suppose I could use a Dropbox link but don't want to post that publicly. It'd be nice if anyone finding this later could access it but... I've sent it...
  9. Replies
    65
    Views
    17,015

    I started the onboarding process about five weeks...

    I started the onboarding process about five weeks ago and haven't heard anything back from them. I have started to use them for supplies since their cut aluminum pricing is actually really good for...
  10. Replies
    62
    Views
    5,992

    I always weld aluminum hot and fast - I rarely...

    I always weld aluminum hot and fast - I rarely stack dimes, always more flattened. Makes a good weld but won't win beauty contests. The smut you see there is some crap that floated up out of the...
  11. Replies
    62
    Views
    5,992

    Yeah for before the PP.

    Yeah for before the PP.
  12. Replies
    63
    Views
    4,183

    Best I can figure the 5V is generated on the main...

    Best I can figure the 5V is generated on the main board's power supply sub board or on the main PCB itself. I can't find any TTL (3.3V) signals anywhere so I think those stay on their respective...
  13. Replies
    63
    Views
    4,183

    So I traced everything I could and as far as I...

    So I traced everything I could and as far as I can tell, there is only one source of 24V DC power in the machine, and that is a 24V DC Switching power supply.

    I can try to scan a few pages of the...
  14. Replies
    63
    Views
    4,183

    It is a sub panel so it has its own safety...

    It is a sub panel so it has its own safety grounding rods but the equipment ground is not bonded to neutral until back at the main supply at the house as required by code.

    I found a few really...
  15. Replies
    62
    Views
    5,992

    So I sent off my first consulting project...

    So I sent off my first consulting project estimation earlier this week. I'm starting at the low side for on-site pricing, but basically I figure I need to be making what I "could" be making with my...
  16. Replies
    63
    Views
    4,183

    Okay, so I got my transformer in... still waiting...

    Okay, so I got my transformer in... still waiting on that power board. I actually have orders waiting at this point but not enough $ to justify getting a tech on site.

    Here is the transformer...
  17. Replies
    1
    Views
    300

    Did you talk to Yamazen?

    Did you talk to Yamazen?
  18. Replies
    63
    Views
    4,183

    The power is sent from the main PCB in the back...

    The power is sent from the main PCB in the back to somewhere in the cabinet with all the relays and breakers, and split from there into the different places including the CRT. So there is one cable...
  19. First thing I'd do is check the capacitors.

    First thing I'd do is check the capacitors.
  20. Replies
    2
    Views
    305

    I was going to head over since I would be in the...

    I was going to head over since I would be in the area anyways, mostly just to stop by a few booths and say "hi" to some guys I knew would be there. I ended up getting sidetracked, though.
  21. Replies
    27
    Views
    1,381

    Harvey Tool has pretty reasonable prices on their...

    Harvey Tool has pretty reasonable prices on their saws - I was surprised that their solid carbides are usually cheaper than the brazed saws we got from other suppliers.

    I'm glad I saw this thread...
  22. Replies
    16
    Views
    881

    If you've got a laptop with a 3.5mm microphone...

    If you've got a laptop with a 3.5mm microphone input you can actually solder together a quick protective circuit using a few cents worth of diodes and use free oscilloscope software instead of buying...
  23. Replies
    16
    Views
    881

    Can you reload it with the 7-segment LED and...

    Can you reload it with the 7-segment LED and rotary switch/pushbutton directly in the control cabinet? I just had to learn to do that today on my 0i LOL...
  24. Replies
    63
    Views
    4,183

    That's my theory, and the tech agreed. I am...

    That's my theory, and the tech agreed. I am waiting on Amazon (damn I miss Radio Shack) to deliver the last few capacitors I need to chase that down.
  25. Replies
    63
    Views
    4,183

    Okay I've got it figured out. I can pick up what...

    Okay I've got it figured out. I can pick up what I'd need for like $80 shipped off eBay. 1.5kVa 240V PW, 24V SW which will bring me down to 216V and be enough to run my current machine (no pun...
Results 1 to 25 of 562
Page 1 of 23 1 2 3 4