Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TeaJunky

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    386

    Just checked my cable again here to make sure and...

    Just checked my cable again here to make sure and I don't have the additional connections hope the info helps.
  2. Replies
    11
    Views
    386

    I have checked my cable here it is the top one

    I have checked my cable here it is the top one
  3. Replies
    11
    Views
    386

    Did you cut the null return cable? Why? My...

    Did you cut the null return cable? Why?

    My setup is as follows win 7 laptop + usb to serial adapter+ null return 9 to 25 pin cable working with this for over 12 years. You should have tried a old...
  4. Replies
    11
    Views
    386

    To receive press list programs button then arrow...

    To receive press list programs button then arrow key down the list of programs(if any) to all this will highlight it, then press receive rs232 button you should see waiting in the bottom corner of...
  5. Replies
    8
    Views
    1,403

    Can I ask before you buy this emulator have you...

    Can I ask before you buy this emulator have you tried a floppy on your machines old floppy drive to make sure it was working, before you removed it.
  6. Replies
    8
    Views
    1,403

    If the USB floppy emulator you have tried is the...

    If the USB floppy emulator you have tried is the 1.44mb version, try the 720k version of the emulator instead this has worked for me. It was a compatibility issue as the machine was a 1984 vintage...
  7. Looking for NC alarm list for Hitachi seiki hi-cell

    Anyone have the NC alarm list and descriptions for a Hitachi Seiki Hi-cell 23b xyzc+b and sub spindle secrios III control. I have found manuals online but some alarm numbers and descriptions are...
  8. I am trying not to guess what the problem may be....

    I am trying not to guess what the problem may be. I have an Hitachi seiki here It has two power supply's 1 mounted in the control rack and 1 below it. I do know that if the power supply below the...
  9. That would be correct. Unfortunately I do not...

    That would be correct. Unfortunately I do not know anything about your type of machine component layout to be of any help to you.
  10. Check to see if the actual control power supply...

    Check to see if the actual control power supply itself is turning on.
  11. I am making progress I need to change a parameter...

    I am making progress I need to change a parameter according to other models of hitachi seiki machine manuals (of course not all the same parameter number) that I have found however the manual I have...
  12. This may be a silly question but have you this...

    This may be a silly question but have you this machine backed up?
  13. Thanks very much for your reply. In other hitachi...

    Thanks very much for your reply. In other hitachi manuals that I have found the 712 alarm is described as you have said above however the alarm I have is renumbered as alarm 714 in those manuals but...
  14. Q setter Tool Nose Point Interlock alarm 712

    I have an Hitachi seiki hi cell with the following alarm 712 Tool Nose Point Interlock in Q setter mode. I am hoping somebody who would have operated these lathes may know how to clear this alarm. I...
  15. Replies
    18
    Views
    2,674

    I think the deciding factor may be how you...

    I think the deciding factor may be how you dispose of the vfo you may have a good enough trade in value against the new Haas machine and making room for your new machine at the same time. If you are...
  16. Replies
    6
    Views
    777

    If a replacement is easy to get where you are go...

    If a replacement is easy to get where you are go that way. I just built up the edges with weld and ground down again. At the time I would have rather got the new ring and I always intended to get a...
  17. Replies
    6
    Views
    777

    Hello I have a 94 vfo as well I had a similar...

    Hello
    I have a 94 vfo as well I had a similar problem a long time ago in my case it was the shot pin ring itself if my memory serves correctly there wasn't much wear on it just at the outside edges...
  18. Replies
    26
    Views
    2,098

    Can I ask is there anything that can be done to...

    Can I ask is there anything that can be done to backup safeguard the actual control itself I am not talking about parameter,settings etc they are already backed up. If you have a control pcb failure...
  19. I got the parameters today but still trying to...

    I got the parameters today but still trying to backup the plc Ladder/Sequence. I can get access to the program with the write enable switch but no output/save option is available that I can see....
  20. Replies
    26
    Views
    2,098

    A guy has attached a probe for work setting and...

    A guy has attached a probe for work setting and done it with the skip signal he has explained how he did it and shows it working in a you tube video link. However he has done all this on another...
  21. Replies
    12
    Views
    1,584

    I was talking to a supplier today and they are...

    I was talking to a supplier today and they are suggesting I use 7075-t651 cold work stress relieved and they also suggested I consider 2618 as an option. Maybe I am wrong here but I thought when you...
  22. I didn't attempt it yet, can I ask did you output...

    I didn't attempt it yet, can I ask did you output you ladder programme to?
  23. Replies
    27
    Views
    1,814

    Thanks for noticing the way I wrote the reply I...

    Thanks for noticing the way I wrote the reply I have removed the reference to the color of the line while I could still edit the post.
  24. Replies
    27
    Views
    1,814

    I suppose with everything people try to repair we...

    I suppose with everything people try to repair we are trying to avoid buying expensive replacement parts that we then find that we didn't need, we all fall into that trap and often more than once. It...
  25. Replies
    27
    Views
    1,814

    If you are certain that this module is your...

    If you are certain that this module is your problem buy the new one. The zener diode will also have a line around it at one end like the line you see around an ordinary diode they usually fail short...
Results 1 to 25 of 33
Page 1 of 2 1 2