Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: mjk

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. "I THINK the 5XX series are actually easier?" ...

    "I THINK the 5XX series are actually easier?"

    nah, because the wires are bigger....

    With all the wiring connections at the right side of the lathe and the swing out panel, there may be clues...
  2. RE wiring 220/440 Mine had a nameplate adhered...

    RE wiring 220/440

    Mine had a nameplate adhered to the "boss" of the shift lever that had the voltage , motor rpm , motor hp,transmission gear qty
  3. Replies
    14
    Views
    584

    If using the walnut shells dry,use breathing...

    If using the walnut shells dry,use breathing protection
    I opened the closed tub after the parts were running for a while
    Dropped me to the floor
    Foretunatly shop door was open and a good 15...
  4. Replies
    2
    Views
    208

    Thanks for all the replies LOL I asked the...

    Thanks for all the replies LOL

    I asked the customer if I could try drilling and tapping the drop that would be cut from the blank.
    Turns out that only the teeth and a shallow depth below the...
  5. Replies
    2
    Views
    208

    Tapping 8-32 blind hole in R60 material

    I haven't had to tap that many holes in hard material, except for when I work hardened 304

    I have a small gear rack that was induction hardened 1045.
    The rack was supposed to be 1045 , not...
  6. The more "sketchy" setups you do you learn more...

    The more "sketchy" setups you do you learn more of the limits of what mini-squall remnants of material are needed to hold a part before becoming a helicopter.
    I have done my fair share, always have...
  7. Replies
    6
    Views
    534

    I'd appreciate the (2) DA200's PM on the way...

    I'd appreciate the (2) DA200's
    PM on the way
    Mike
  8. Thread: G76 threading

    by mjk
    Replies
    16
    Views
    753

    "GO X4.525" What is the Z value at this start...

    "GO X4.525"

    What is the Z value at this start point?
    It has to be larger than the finish point
  9. Thread: G76 threading

    by mjk
    Replies
    16
    Views
    753

    "It currently has x spindle center line of 4.o X"...

    "It currently has x spindle center line of 4.o X"

    What are the G54-G59 values for X?
  10. "but the exactly placement of those spaces is...

    "but the exactly placement of those spaces is not"

    Can the locations for each owner be detailed and added to all the owners deeds?

    Who is responsible for the upkeep of the lot(blacktop,...
  11. Maybe Bill with an orange reflective suit and ...

    Maybe Bill with an orange reflective suit and flashing wands?
  12. "but time is money and the time it takes to...

    "but time is money and the time it takes to identify",

    The original post took some time to put together...he's halfway there

    I'd suggest picking a few of each size and see what Ebay brings....
  13. I was having a problem about a year ago with...

    I was having a problem about a year ago with people parking in my "ally" that is on my property and the neighbors.
    Its also the emergency access for the back of my neighbors building in case of...
  14. I've been using wd40 on aluminum in manual...

    I've been using wd40 on aluminum in manual operations
    Does the CRC3-36 perform same way for aluminum ?
  15. Replies
    20
    Views
    925

    For me it's easier to send the program back to...

    For me it's easier to send the program back to the PC.
    Add comments especially date run and updated revision #
    It's ready to use next time with all the reminders
  16. Replies
    2
    Views
    696

    As built drawings 101 after March 2020

    I've been working with a customer since June of last year on a project that involved a different engineer than usual and many unknowns and unusual requests.
    Without getting into detailed specifics,...
  17. Thread: NOGA Lot

    by mjk
    Replies
    4
    Views
    971

    Noga lot received today well packed and all look...

    Noga lot received today well packed and all look new

    Thanks!
  18. "without the sloobber ?" That's almost funny,...

    "without the sloobber ?"
    That's almost funny, they drool as bad.

    There are "dry mouths" and "wet mouths"
    Mine is on the lighter side of a wet mouth.

    Any carb(pizza,bread, Cream of Wheat...)...
  19. "Is there any DOG under all that FUR ?" Trevor...

    "Is there any DOG under all that FUR ?"

    Trevor
    140lbs of Newfie.
    He is a rescue.(after I swore I wouldn't get another dog at my age 3 years ago)
    Has as much energy and speed as a Jack Russel...
  20. Took a trip yesterday afternoon from northern...

    Took a trip yesterday afternoon from northern Delaware to "the first Wawa south of the Bay Bridge" on 301 in Maryland,about 90 miles.
    My daughter lives in DC and works outside the city as an...
  21. Thread: Geometric dies

    by mjk
    Replies
    6
    Views
    626

    pm on its way

    pm on its way
  22. DE issued stay at home as of 8 this morning I'm...

    DE issued stay at home as of 8 this morning
    I'm carrying a supply of my business cards which has my title and a web address showing I'm manufacturing a product that indirectly supports medical and...
  23. Thread: Geometric dies

    by mjk
    Replies
    6
    Views
    626

    I may be interested depending on what head they...

    I may be interested depending on what head they fit
  24. Thread: NOGA Lot

    by mjk
    Replies
    4
    Views
    971

    Email on its way Mike

    Email on its way
    Mike
  25. Replies
    24
    Views
    3,368

    Its Tuesday the 17th and tomorrow I'm attending...

    Its Tuesday the 17th and tomorrow I'm attending the funeral of someone I've only known for about 5 years.
    He worked part time at an auto shop next door.
    Always had something nice to say,...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4