Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Technical Ted

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    354

    Does it have the bronze bearings or ball...

    Does it have the bronze bearings or ball bearings? I have a B&S 2B SG that had the spindle replaced with a Pope cartridge type spindle and I use Mobil #6 spindle oil in that. I'd probably use...
  2. Replies
    7
    Views
    593

    That "keeping your lathe in trim" PDF tells you...

    That "keeping your lathe in trim" PDF tells you how to properly remove your spindle so you should be all set there. Easy Peezy!

    Ted
  3. Replies
    7
    Views
    593

    Your spindle should turn nice by hand... If it...

    Your spindle should turn nice by hand... If it doesn't, then I would do some troubleshooting.

    What oil are you using? I use Mobil #10 spindle oil which is the recommended oil. Other oils may...
  4. Replies
    15
    Views
    2,679

    I have an older 15" SB with "oil" stamped on it,...

    I have an older 15" SB with "oil" stamped on it, so I use oil on that one. My newer SB13" is stamped "grease" so I use "SuperLube" on that one.

    Super Lube 41150 Synthetic Multi-Purpose Grease,...
  5. Replies
    7
    Views
    593

    Are you experiencing some type of problem that...

    Are you experiencing some type of problem that would suggest lack of lubrication? Is the spindle seezing up? Are the bearings getting hot?

    My SB13 uses a very small amount of oil in several weeks....
  6. Replies
    25
    Views
    10,399

    Is the piece to be threaded something you can put...

    Is the piece to be threaded something you can put in a lathe to single point? I've had good luck single pointing both right and left hand 1/2"-10 acme nuts by silver soldering a HSS tool bit on a...
  7. I have one of those, complete. Bought it new old...

    I have one of those, complete. Bought it new old stock from a high school. Those tips are carbide on mine. I'm sure they are not as good as an air bearing Weldon, but it works fine for me. I'm a...
  8. Here are the requested measurements: I measured...

    Here are the requested measurements: I measured threads per inch as close as I could with a good scale. 10 turn distance traveled measured by depth mics for accuracy.

    Top Slide:
    Screw = 12-3/4...
  9. Thanks for the reply! I'll do that and post...

    Thanks for the reply!

    I'll do that and post results when I post the screw measurements later today. But, as I posted in my first post, I put a dial indicator on the slide and one full rotation of...
  10. Thanks for the reply Larry. I was hoping you...

    Thanks for the reply Larry. I was hoping you would do so.

    I didn't post the number of divisions on the dials, because they are shown in the pictures, but the dials have 200 divisions. The numbered...
  11. Hardinge Cataract lathe with metric compound slide dials!!??!!

    Just wondered how common these are. I never dreamed that a piece of equipment made in the USA in the 1940's??? would have metric dials, but I'm convinced this one does. Dang! Maybe the slide is a lot...
  12. Replies
    8
    Views
    680

    Larry, Jim told me the type of oil he uses...

    Larry,

    Jim told me the type of oil he uses (thanks Jim). What oil do you typically use? I have 3 light weight Mobil spindle oils on hand and am hoping to be able to use one of those.

    I'm not...
  13. Replies
    8
    Views
    680

    Thanks Larry! Ted

    Thanks Larry!

    Ted
  14. Replies
    8
    Views
    680

    Thanks for the reply! Great information. I'm...

    Thanks for the reply! Great information.

    I'm talking about rotating the spindle by hand with the belts disconnected. We had to break everything down to get it out of the PO basement. So, is the...
  15. Replies
    8
    Views
    680

    A few more pictures for those interested: ...

    A few more pictures for those interested:

    Ted273918273919273920273921273922
  16. Replies
    8
    Views
    680

    Hardinge Cataract lathe questions

    A few questions for you that are familiar with these gems. First, a short background. I'm a retired hobbyist. I already had a 15 and 13 inch lathes (along with 3 mills, SG, shaper, T&C grinder, etc.)...
  17. I, too, am teaching myself tig welding. I asked...

    I, too, am teaching myself tig welding. I asked the same question about dabbing or steady moving and the guys I used to work with that weld at a pressure vessel factory told me to do the dab method....
  18. When I'm looking for CAD files I always check...

    When I'm looking for CAD files I always check grabcad.com

    Ted
  19. Google South Bend's book "How to Run a Lathe". It...

    Google South Bend's book "How to Run a Lathe". It will be a great resource for you. You can download it for free from several sites.

    Ted
  20. A couple more... 271550 271551

    A couple more...

    271550
    271551
  21. It was a pretty machine. I had a "shaper wanted"...

    It was a pretty machine. I had a "shaper wanted" ad and he sent this to me before he listed on Craig's List. I turned it down because I already have a 7" Rhodes and want something a little larger.
    ...
  22. Replies
    70
    Views
    6,589

    Jet sells parts directly at: Jet Parts Store...

    Jet sells parts directly at: Jet Parts Store

    I would check there first to get their list price and then do some Googling and see if you can find better pricing elsewhere.

    Ted
  23. Replies
    5
    Views
    1,172

    Yes, I do agree with that. You are correct. I...

    Yes, I do agree with that. You are correct. I over simplified.

    Thanks,
    Ted
  24. Replies
    5
    Views
    1,172

    They would need to be the same size or the belt...

    They would need to be the same size or the belt wouldn't fit properly for the different steps.

    Ted
  25. Replies
    7
    Views
    3,144

    Another thing came to mind... how many, if any,...

    Another thing came to mind... how many, if any, wheel adapters come with it? These things are expensive, like $65 each new. You'll need at least one. I have 4 for different wheels and that works OK...
Results 1 to 25 of 156
Page 1 of 7 1 2 3 4