Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter.

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. WTD: Angular contact spindle bearings - inch sizes 1.0 x 2.5 x 0.75"

    I know it's a bit of a long shot but I'm looking for a pair of angular contact spindle bearings for my old surface grinder:

    ID 1.000"
    OD 2.500"
    W 0.75"

    If anyone has a lead on who might have...
  2. I replaced the bulb holder contacts in the green...

    I replaced the bulb holder contacts in the green button on mine to take a modern style bulb.

    https://www.practicalmachinist.com/vb/monarch-lathes/modern-lamp-green-button-265044
  3. Replies
    58
    Views
    3,254

    Congrats and well done. Your machine is very...

    Congrats and well done. Your machine is very similar to my 16303 except mine has ELSR. I also got the 2J chuck and 39 collets though I had to find a steady later and I didn't get a stop. Mine also...
  4. I have one on mine. It locates the tail of the...

    I have one on mine. It locates the tail of the machine into a hole in the storage box, otherwise it serves no use except as something to keep an eye on as it tends to work loose and fall out.

    I'll...
  5. What is this part that someone would want to...

    What is this part that someone would want to specify such a thread in it?
  6. Replies
    17
    Views
    1,507

    I just cut felt wipers for my surface grinder...

    I just cut felt wipers for my surface grinder from this:

    Felt Furniture Pads FJSM 1 Roll Felt Floor Protector Pad Felt Tape Self Adhesive Furniture Pad Sticky Felt Pads Heavy Duty Thick Felt...
  7. Replies
    16
    Views
    1,332

    I made one a couple of weeks ago from 95 shore...

    I made one a couple of weeks ago from 95 shore rubber. Had 3 failed attempts at cutting one out with a hacksaw so I cut one over-sized and ground the sides flat on my bench grinder.

    I didn't think...
  8. That's why I put the description in the post, so...

    That's why I put the description in the post, so people could google them.

    CARBON BRUSHES for Narex: ESV, ESO10, EV 108D, EV406, EV408, EV410, EV710 E126: Amazon.co.uk: Car & Motorbike
  9. The Metabo Jigsaw motor internals ST EP 564/565...

    The Metabo Jigsaw motor internals ST EP 564/565 fit perfectly. They come up all the time on eBay. If you're lucky enough to find the model without the top handle I do believe it's a direct fit...
  10. Brushes: Blue Biax brushes -...

    Brushes: Blue Biax brushes -

    Speed control: Retro-fit speed control to old Biax 7 EL

    Can't help with the brush caps but as I said I would just make them, they are a simple part.
  11. 'Ang on I have a source for brushes. I'm sure......

    'Ang on I have a source for brushes. I'm sure...

    BTW John you can make that 7EL vari-speed by removing the switch and robbing the speed control from a £20 Aldi/Lidl grinder - plus you get the...
  12. Replies
    4
    Views
    513

    I think your crunchy action is more likely to be...

    I think your crunchy action is more likely to be the thrust bearing. Since your machine is a copy of the 10EE you should find the support block and bearings at the far end of the screw.
    The front...
  13. Replies
    4
    Views
    456

    I believe I made mine from a M10 socket cap. 12.9...

    I believe I made mine from a M10 socket cap. 12.9 grade (similar to your 'grade 8' I think). Had to turn down the head a bit and make sure you find one with a long enough shoulder.

    Check the base...
  14. Eagle grinder spindle and way lube? What would you do?

    I'm rebuilding a small manual grinder - an Eagle Mk3 W. Got nearly all of the scraping work done and I'm looking for advice on a couple of bits.

    Despite sitting under a tarp for 10 years the...
  15. Replies
    9
    Views
    1,011

    Nice follow-up Bill. BTW I have a couple of...

    Nice follow-up Bill.

    BTW I have a couple of spare braking resistors salvaged from a lift motor control if you ever need one. I have one of them fitted in my HLV cabinet for braking with the vfd.
  16. My step chuck body has no markings but my drive...

    My step chuck body has no markings but my drive plate carries the serial EE 2597
  17. Replies
    5
    Views
    1,001

    I think that's great Mark. Well done for sticking...

    I think that's great Mark. Well done for sticking with it after 5 failed castings too.
  18. As above the bolt clamps the taper attachment...

    As above the bolt clamps the taper attachment bar, the recessed socket cap holds the cross slide nut and the recessed slotted head is the backlash adjuster for the cross slide nut.
  19. Replies
    557
    Views
    93,644

    Thanks Rich yes the whole groove is land-locked...

    Thanks Rich yes the whole groove is land-locked so I'll just scrape over it. The adjacent bolt-on gib also had similar damage but I milled it out then scraped that flat.
  20. Replies
    557
    Views
    93,644

    Currently working on a Eagle surface grinder. I...

    Currently working on a Eagle surface grinder. I got the knee scraped in, here's the z-axis way on the knee.

    273550

    Y axis is pretty good too little bit more to do on it but the bearing is good...
  21. Replies
    11
    Views
    1,102

    You might want to try Cannon engineering...

    You might want to try Cannon engineering in Leeds they do gear cutting. The owner knows a bit about automotive gears as he's a top fuel bike racer.
  22. Replies
    21
    Views
    5,482

    Check the lines, my cross-slide feed lines were...

    Check the lines, my cross-slide feed lines were plugged up solid.
  23. I have thinned canode with ordinary tap water -...

    I have thinned canode with ordinary tap water - just a few drops in the 1.5ox bottle. It caused no issues. The yellow ink had thickened over a couple of years.
  24. Replies
    6
    Views
    783

    I agree, that one is half-inch taller from the...

    I agree, that one is half-inch taller from the bottom flat to the split than my round-dial steady. Mine is 6.25"
  25. Rich, I don't know what to say, I'm very touched....

    Rich, I don't know what to say, I'm very touched. Thank you.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4