Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: michiganbuck

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Qt[As it is, they are just giant frauds...

    Qt[As it is, they are just giant frauds exploiting a so-called 'loophole'.]
    Correction some: of them..IMHO
  2. Replies
    6
    Views
    496

    QT: [My thinking is i could replace the #2 and...

    QT: [My thinking is i could replace the #2 and the KO Lee with the #13. You could but not without problems.

    The 13 will make a decent surface grinder, but check to see how much cross travel you...
  3. interesting... Raging Against Self Defense - A...

    interesting...
    Raging Against Self Defense - A Psychiatrist Examines The Anti-Gun Mentality | Buckeye Firearms Association
  4. Good to have drawings or photos at your grinding...

    Good to have drawings or photos at your grinding station to look at when doing ends. Very often the cut-in or gashing to center is done by hand and looking at a end drawing can help you do that...
  5. QT Kurt: And make NRA Gun Safety Classes as...

    QT Kurt: And make NRA Gun Safety Classes as common in public schools as classes in driving safety and health/nutrition.

    Very good point but it seems the majority of teachers are not in favor, or...
  6. The do-gooders are are gaining numbers and so...

    The do-gooders are are gaining numbers and so likely will get their way.. I don't see how we gun advocates will save the right..Except to get more people involved in proper/safe gun use.
    Country...
  7. Replies
    8
    Views
    589

    For much fancy grinding the dilemma is is...

    For much fancy grinding the dilemma is is dressing or retaining a form or sharp corners and shapes so the tool shape can be made in one or few passes, or being able to make a number of passes that...
  8. Replies
    23
    Views
    1,347

    Perhaps a left helix, right hand cut end mill ...

    Perhaps a left helix, right hand cut end mill would tend to push down on the part to push it to have more support and less chatter..

    Could a ball nose probe/finger set just above/near and...
  9. I sharpened single flutes in a model B type from...

    I sharpened single flutes in a model B type from Eldorado/Star and double flutes through a close size bushing and the tail end on a center, with the lip edge below center for clearance..then drop to...
  10. Are you doing your own sharpening? Mostly gun...

    Are you doing your own sharpening? Mostly gun drills?
  11. Q:[ Is secondary clearance needed on the end of...

    Q:[ Is secondary clearance needed on the end of end mills?] YES
    The primary at perhaps 5 or 7* (and more)just ground off the edge likely will leave an area below the cutting edge and before the...
  12. Watching the Hong Kong news yesterday I saw a guy...

    Watching the Hong Kong news yesterday I saw a guy drop a hand gun..Go figure guns are not allowed in Hong Kong. Very likely the Hong Kong cops are looking for that guy..

    Keep and Bear Arms - Gun...
  13. Replies
    8
    Views
    589

    The Cincinnati #2 is the hot rod machine for...

    The Cincinnati #2 is the hot rod machine for sharpening simpler work like mill cutters, reamers gun drills, hobs, slash point drills. needs an air spindle to do small sprials. can do fancy work with...
  14. Replies
    8
    Views
    589

    I have not run the Deckel s11 but it looks like...

    I have not run the Deckel s11 but it looks like it has many features of the Monoset and perhaps even more. I think it would out grind the KoLee.. the Deckel dressing features are/seem very capable so...
  15. Guess you need to consider dimension "A" fitting...

    Guess you need to consider dimension "A" fitting your intended use.
    The on you show is so one can turn it around so one might use both the front and rear wheel edge with one dressing..I have never...
  16. Replies
    27
    Views
    1,377

    QT:[That's a very good idea, I've never...

    QT:[That's a very good idea, I've never considered turning an arbor in my mill before.]
    With the arbor made/turned in an end mill holder , mark the spindle nose, the holder and the arbor so...
  17. Replies
    27
    Views
    1,377

    I ended up there because my saw was running out...

    I ended up there because my saw was running out like a mother.....
    Twooooooo that arbor away or fix it...should run perhaps .002 or better for diameters and sides.

    .0001 per tooth. Any more an I...
  18. Replies
    11
    Views
    871

    A recess wheel can be put on a 13 grinder so the...

    A recess wheel can be put on a 13 grinder so the wheel holding nut does not stick out and then the 13 grinder can grind a short dovetail with the part fixtured.
    long travel about 22" so a 20" long...
  19. Many surface grinders have about 1" at big end...

    Many surface grinders have about 1" at big end and some about 7/8 at big end...
    Your grinder about 1" is the most standard for smaller surface grinders..Yes likely the one your friend mentioned is...
  20. Replies
    30
    Views
    2,140

    With the thread for a set screw and full thread...

    With the thread for a set screw and full thread needed to to extract the screw is one reason for such design.....who knows.. only the guy who designed the part.. Suckering the customer for more than...
  21. Replies
    14
    Views
    1,265

    Super nice..could have used that in sharpening...

    Super nice..could have used that in sharpening and making cutting tools.
  22. Replies
    11
    Views
    871

    With having a 13 grinder you can use the machine...

    With having a 13 grinder you can use the machine as a precision measuring device. Set the part on the table squared up perhaps clamped to an angle plate...and then with an indicator mounted to the...
  23. Replies
    11
    Views
    871

    Guess I should and that fitting/feeling the...

    Guess I should and that fitting/feeling the cutter into the part for determining the correct angle often does not work well. The cutter flutes may not be exactly at/on center for the length of the...
  24. Replies
    65
    Views
    4,008

    Gordon would know, He knows all about...

    Gordon would know, He knows all about threads....where is Gordon?

    Ops..OT:
  25. Replies
    65
    Views
    4,008

    Newbs might expect to take it on the chin once or...

    Newbs might expect to take it on the chin once or twice and not upset..could have saved the broken and brazed it back to ok...or not.

    but once the argument starts the the thread is busted.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4