Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: hsracer201

Page 1 of 22 1 2 3 4

Search: Search took 0.01 seconds.

  1. Ted - [email protected] or ebay. Those are your...

    Ted - [email protected] or ebay. Those are your two best choices.
  2. Replies
    11
    Views
    1,099

    Everybody wants capitalism until its time to do...

    Everybody wants capitalism until its time to do some capitalism stuff and then they complain about it. I don't get it.

    Who cares what people ask for their stuff? If it sells for $10,000...
  3. Replies
    13
    Views
    1,182

    The 56 goes on the gearbox, the 80 goes on the...

    The 56 goes on the gearbox, the 80 goes on the banjo idler. Both are on eBay I’m sure. I think I saw damienpdr list some yesterday.

    Edited to add: that’s for a double tumbler machine. I can’t read...
  4. Replies
    12
    Views
    1,242

    I ran across one of those in a box of stuff that...

    I ran across one of those in a box of stuff that came with a heavy 10 once. I knew I’d never use it so I popped it on eBay for $500 and it sold very quickly.
  5. Replies
    9
    Views
    2,897

    This thread is 12 years old and none of these...

    This thread is 12 years old and none of these guys post here anymore.

    Look in this thread and see if it has the info you need:

    Motor drive pulley diameter for south bend 9" lathe
  6. Replies
    24
    Views
    2,692

    The PRI 3 piqued my curiosity a little bit so I...

    The PRI 3 piqued my curiosity a little bit so I found all the old cards I’ve bought through the years and none of them make mention of it. The oldest card I have is 1945 though.
  7. Email him directly. [email protected]

    Email him directly.

    [email protected]
  8. Watch a bunch of Tubal Cain videos on YouTube. If...

    Watch a bunch of Tubal Cain videos on YouTube. If it has been idle for that long it probably needs new wicks to carry lube to the various shafts and bearings.
  9. The only helpful info I can say is a VFD’s do not...

    The only helpful info I can say is a VFD’s do not like drum switches, they need to go straight to the motor. Skip all this work if you’re going to use one.
  10. Replies
    3
    Views
    739

    There’s nothing to adjust on the spindle. Make...

    There’s nothing to adjust on the spindle. Make sure the detents fall into place and tighten the hex key bolts.

    If adjustments are needed they are made screwing the mating stud in or out of your...
  11. Replies
    3
    Views
    650

    Two clutches?

    Two clutches?
  12. Replies
    19
    Views
    3,198

    Put all the chips you can scrape loose in a jar,...

    Put all the chips you can scrape loose in a jar, then clean it up and repair as necessary.
  13. Remove your spindle and pull everything off down...

    Remove your spindle and pull everything off down to the bull gear. Clean the little groove the spring engages. Then put everything back. Shouldn’t take much more than 30 minutes. You can also tweak...
  14. Replies
    1
    Views
    617

    He sold his shop and retired. Check with Ted....

    He sold his shop and retired.

    Check with Ted.

    [email protected]
  15. This should help. Copy and paste as necessary if...

    This should help. Copy and paste as necessary if it doesn't link. You will need adobe to open it.

    http://www.neme-s.org/Shaper%20Books/South%20Bend/CE3458%20Parts%20Manual.pdf

    The book off...
  16. I had to check my serial number as I knew it was...

    I had to check my serial number as I knew it was close to yours, mine is 22659R.

    You could run that little motor on 14awg, but I would suggest paying just a little bit more up front and running...
  17. Replies
    2
    Views
    803

    You didn't get the 9a they auctioned off at...

    You didn't get the 9a they auctioned off at Verina High School, did you?
  18. ETA: OP replied while I was typing this out. ...

    ETA: OP replied while I was typing this out.

    Believe it or not, the rear gib tightness can influence how much the front can be lifted to some degree. This is only usually noticeable if the apron...
  19. I just had a 4.5' bed heavy 10 shipped 1/2 way...

    I just had a 4.5' bed heavy 10 shipped 1/2 way across the country for $179, so I'd guess $135 or so to ship it most places by freight on a pallet.
  20. Replies
    8
    Views
    713

    Can you clarify something for us? Take the thread...

    Can you clarify something for us? Take the thread dial off the lathe and while it is in your hand does the gear spin in sync with the dial? Can you make it slip?
  21. Replies
    8
    Views
    713

    It isn't going to turn the top part while...

    It isn't going to turn the top part while engaged...

    That only turns till you lift the handle.
  22. Replies
    8
    Views
    814

    He’s looking for a later (newer) style. That’s an...

    He’s looking for a later (newer) style. That’s an older style.
  23. Replies
    14
    Views
    1,482

    No, not without pulling the variable speed drive...

    No, not without pulling the variable speed drive and then removing the motor. Besides, it isn’t a 220/440 motor, it’s a 440 motor. I know how to change between the two when it’s possible.

    No...
  24. Replies
    14
    Views
    1,482

    You want to know how I know you haven't swapped...

    You want to know how I know you haven't swapped motors in a South Bend Fourteen?
  25. Replies
    14
    Views
    1,482

    Bummer, it’s 440. That throws a big wrench in...

    Bummer, it’s 440.

    That throws a big wrench in the plan.
Results 1 to 25 of 529
Page 1 of 22 1 2 3 4