Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Green Machine

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    801

    1350 rpm is 60 sfm, should work well with...

    1350 rpm is 60 sfm, should work well with intermittent lube application. Second on the masonry drills suitably sharpened, I used to use those to drill holes in hardened die steels all the time. ...
  2. I think start it at night and hope it finishes...

    I think start it at night and hope it finishes before morning? I have had 1/2 hour videos take 4 or 5 hours if I recall. But usually I just start them when I am not using my computer and just let...
  3. Yes I love it too. Found a di filter and a...

    Yes I love it too. Found a di filter and a solenoid on eBay. Easy setup. Thanks for the pics and description. Only just got it working, far too busy with paying work to be messing around with a...
  4. Replies
    25
    Views
    1,741

    I used to use a dijet mirrorball in 1/4" where I...

    I used to use a dijet mirrorball in 1/4" where I used to work. Logged thousands of hours surfacing hardened die steels. Tool bodies lasted a long time, and the inserts were very repeatable. I used...
  5. Anyone? I have a wire hanging out of the control...

    Anyone? I have a wire hanging out of the control box and capped off, would this go to the solenoid that I think should be there to allow water thru, or bypass the di bottle.
  6. Brother hs-300 resin bottle setup, missing from machine

    Hello, just checking to see if anyone has, or could take a couple of good pictures of the resin bottle setup. Also, if anyone knows how the system works? Is there a solenoid or something that opens...
  7. Replies
    17
    Views
    1,284

    Right lane passer. Looks like he tried to shoot...

    Right lane passer. Looks like he tried to shoot the gap into the middle , misjudged, and over corrected. Serves him right, I hate those impatient assholes.
  8. Replies
    7
    Views
    1,270

    Make sure to leave room for your forklift to turn...

    Make sure to leave room for your forklift to turn in with whatever size dies need to fit in the press. I know these are only small ones, but the larger ones you have will probably need to be loaded...
  9. Back mounting is old school. Much easier to snug...

    Back mounting is old school. Much easier to snug up punch holder when you need to knock them around for die alignment before dwelling them to shoe. I always hated having to reach into a die to...
  10. Replies
    1
    Views
    427

    My old okk with a mits 320 control, you go into...

    My old okk with a mits 320 control, you go into the parameter switch page, change 17 to on(which is the auto tool change reset), turn the manual feed knob to plus (+), make sure you turn it back to...
  11. Because most of us make a living at this, and...

    Because most of us make a living at this, and don't have time to go over the same basic questions over and over.
  12. You gain control in a prog die by having a way to...

    You gain control in a prog die by having a way to
    hold the part in place. Your carrier attaching it to
    the strip allows you to work a pressure pad into the
    forming operation, and control timing. I...
  13. Replies
    39
    Views
    4,176

    Right on, always wondered when you were going to...

    Right on, always wondered when you were going to make the jump. Your shop's better than mine ;) good luck and prosperity in the times ahead.

    Mike
  14. I would like to be in imperial as that is what I...

    I would like to be in imperial as that is what I use day to day, my other machine is imperial, as are all of my tool libraries. So if I can get it switched over it would make my life easier. I just...
  15. Issue switching brother tc324n from metric to imperial

    Hello, I am having an issue switching over to imperial. I changed the machine over fine, and restarted, but started getting deviation errors when moving the axes. I looked in the parameters page(i...
  16. What usually gets sold as a null modem cable?...

    What usually gets sold as a null modem cable? It's just crosswired right? I know some cables need to have the pins in the connector jumpered, but I am not sure if that's the same type of cable
  17. Excuse my ignorance, but where do I check for the...

    Excuse my ignorance, but where do I check for the ptp/ptr settings? Is it on the machine? I only see the page for communication in the parameter page. Also it is the g code control.
  18. Which cable for rs232 on brother tc324n

    Which type of cable for rs232 communication? Is it a plain old null modem, or something else? I already have one other cnc that runs a mits 320 control hooked up, but am unsure what cable wiring is...
  19. Robin, check out bohler uddeholm, they have a...

    Robin, check out bohler uddeholm, they have a line of stores called 'the steel store'. The one closest to me (kitchener on) ships cut to order pieces, usually via Canpar. They have been pretty...
  20. Ok gotcha, the work offset is driven by the...

    Ok gotcha, the work offset is driven by the program, not by the pallet. I think now that I have this info from the thread, I should be able to sort it out. Thanks a lot to all who replied.
  21. OK that makes, sense, thanks a lot. I just got...

    OK that makes, sense, thanks a lot. I just got the machine, and haven't had much chance to play with it, too busy with other work :) What about work offsets? say g54 on pallet 1, and g55 on pallet...
  22. Programming pallet change Brother TC324-N

    I have a new to me pallet change machine, what is the code to run separate programs on each side of the pallet? I know there are Mcodes to go to each pallet, but I am not sure how to layout the...
  23. That is the exact same setup I bought 2 years ago...

    That is the exact same setup I bought 2 years ago to run my CNC mill. Motor is reasonably quiet, I have had no issues with the unit overall.
  24. Replies
    44
    Views
    5,840

    No one else is talking about getting paid via...

    No one else is talking about getting paid via credit card. EFT is the same as someone going to the bank and getting cash and giving it to the payee. Once it's gone, it's gone. You have to talk nice...
  25. Replies
    117
    Views
    8,612

    Given this is a manufacturing site, and they have...

    Given this is a manufacturing site, and they have little in the way of manufacturing, i'm not really surprised.

    Spanish does really help, especially given how many countries on this side of the...
Results 1 to 25 of 136
Page 1 of 6 1 2 3 4