Search:

Hi,

Given the location, Fischbach Germany, which is near Idar Oberstein, a major jewelry production area, at least used to be, I would guess it is related some how to jewelry production.

This...

Interesting idea, it is always a challenge to tighten any spindle/draw bar when there is little to nothing to hold on to.

Thanks,
Bob

Thanks for the cast iron alert!

If I use a puller I will make some form of backing plate to slip over the shaft behind the flange and try to gently warm the flange a bit.

I do not expect...

Here are pictures, the .6693 (17mm) is also the bearing bore diameter according to the parts list.


306040306041306042

I figure it is a tight sliding fit but, I don't know why it would have...

Hello

I need help. I am looking for some experience/expertise with a K O Lee Tool and Cutter Grinders. I recently acquired a B300 grinder in good condition. It probably needs new bearings in the...

If I understand the question, I think the that first column is minutes so you can get more refined than whole degrees.

Bob

I put a set of the Blue Max tires on an old Parks/Craftsman 18" wood band saw. It has had light use for about 5-6 years and no problems.

Bob

Ted, thanks for the information to help figure it out, it worked.

Carl?, thanks for the "Simplest way".

Bob

Hi,

My searches have been unsuccessful.

Can anyone tell me the direction the shaper's bull gear should turn looking at it from the access door?

Thanks,
Bob

Scuffy.

I just posted a rough sketch of the Type 4 Head motor pulley in the Type 4 Head album of the Fray Group on groups.io.

The original pulley bore is 1" I believe.

Bob
71193

Scuffy,

Try [email protected] | Topics. If the link does not work search groups.io for Fray, there is a group there. Pictures, manuals etc, some pretty good information and files.

I will try to...

Thermite,

I will take a look a your suggestion. The cost could be quite reasonable for all the pieces parts given I would need some type of 3 Phase overload either way.

By the way you Combat...

Thanks for the reply's.

Stuart, I hope/intend to keep reversing capability.

Phil, the single phase rating for the set is 115V 2HP and 230V 3HP.

SAF, good point on the need for 3 heaters.
...

As asked in the Subject Line. Can this set of Single Phase contactors, wiring diagram attached, be rewired to use Three Phase power.

I am trying to figure it out but I not an electrician. Any...

Thanks, to all. I will use it, I probably would have tried it any way.

Bob

Twice the length of the side opposite the 30 degree angle. If I remember correctly.

Bob

Holescreek, jancollc

Thanks for the info.

Holescreek, twitching after opening would have concerned me a bit, symptoms of nerve agent.

Bob

Hi,

I have an unopened gallon jug of Kool Mist 77 and the manufacture date on it is not legible, probably two to three years old. I know the book recommendation would be dispose of it and buy a...

Also, I doubt they used bar codes and plastic, type material, labels in '53.

Bob

Excellent explanation, hope you received good marks in Geometry/Trig.

Bob

Yep, I have a shipment from New York that has been, according to their tracking data, in their Little Rock facility almost 48 hours now, only 20 miles from my house. I initiated a claim and they are...

You can also try the Rockwell Lathe Group at groups.io

Bob

Rivett608,

I only have the sketches I am making as I get pieces apart and guesses about the internals I can't see yet, especially what holds it together. I appreciate anything you can find, if...

More Pictures.262198262199262200

A bit more information and pictures, unfortunately I could not figure out how to sequence the pictures.

The “new to me” Pratt and Whitney M-1803 is very stiff, cannot be turned by the...