Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Street

Page 1 of 24 1 2 3 4

Search: Search took 0.01 seconds.

  1. pay someone to rebuild the engine properly and...

    pay someone to rebuild the engine properly and install it,test run it.get a warranty. 30 over go 40 if need be no big deal. seized valve in guide no big deal.
    If you don't know about hardened seats...
  2. What about a ultrasonic cleaner anyone had...

    What about a ultrasonic cleaner anyone had experience with them are they any good?
  3. Replies
    31
    Views
    2,497

    see cash who is on PM here Mattison 400S Grinder...

    see cash who is on PM here Mattison 400S Grinder Just Arrived.

    he makes blades but his website knife maker.com is not coming up for me at the moment.

    babbit is no big deal just a few little...
  4. Replies
    9
    Views
    1,069

    Have a poke around the WEG website there is a 6...

    Have a poke around the WEG website there is a 6 pole motor 1175 rpm check hp and type of mounting output etc

    WEG - Selecao de Motores Eletricos


    There is also TECO TECO - Low Voltage...
  5. Replies
    909
    Views
    72,442

    i would just make a new shaft back to spec in...

    i would just make a new shaft back to spec in regard to keys etc watch out for the gear if the bore is oversize though that needs to be checked also the keyways in the components.
    do a good job and...
  6. i suppose a small test stand unit maybe a start...

    i suppose a small test stand unit maybe a start to see if you can load it with sensors doing just one rib and change depth of roller, material has to yield so that would be a start point on a hand...
  7. Replies
    11
    Views
    1,162

    If lucky doesn't take the taper mic i would be...

    If lucky doesn't take the taper mic i would be interested in it.
  8. Replies
    162
    Views
    14,779

    The option to sit when not busy i would think be...

    The option to sit when not busy i would think be a benefit and allow working longer hours, if your not within button pushing distance it would be another matter.
    But you have pissed off your workers...
  9. As for cutting normal wheels with a water jet yes...

    As for cutting normal wheels with a water jet yes you can do it, it leaves a wider kerf though due to the grit coming off grinding other grit.

    Just buy the right shape first time is best water jet...
  10. Replies
    15
    Views
    2,483

    the shop i was at kept a range of common spares...

    the shop i was at kept a range of common spares seals,carbide nozzles. valve both outlet and inlet,diamond offices, rubber grommet for the feeder etc they ran the machine till it broke down and...
  11. For valve seat work to bond the wheel to the...

    For valve seat work to bond the wheel to the centre part i have used Qbond it seem to work well, it was low speed but i suppose it would work as well in a high speed setup.

    here About Us – Q-Bond
  12. try this place they make a deckel clone. I...

    try this place they make a deckel clone.

    I would email them beforehand to see what they can offer and pricing etc.

    New FPS manual machines | FPS Werkzeugmaschinen GmbH

    and here

    Spare...
  13. Replies
    13
    Views
    2,086

    Which lathe did you buy on here Engine Lathes...

    Which lathe did you buy on here Engine Lathes

    added .


    On closer inspection it is pratikant vc plus.....
  14. Replies
    15
    Views
    2,483

    I have used a techni they are made in Australia...

    I have used a techni they are made in Australia the software is made my ANCA most of the machine is made by techni not sure on the pumps now as they changed to a new system.

    As stated can be...
  15. Replies
    26
    Views
    2,154

    Doesn't DG foster make straight edges i am sure...

    Doesn't DG foster make straight edges i am sure he is on this site just search for him in machine reconditioning and scraping section worth a look


    ah here it is 48” Featherweight Camelback...
  16. Replies
    40
    Views
    3,888

    Most likely the best bet to avoid damaging...

    Most likely the best bet to avoid damaging anything would be to send tooling out to a shop with the correct gear get them to mount it and pay a fee for doing it.

    see the tooling provider they may...
  17. I have used auto cad a little, micro station and...

    I have used auto cad a little, micro station and solid works is much different in that you don't have to draw lines true size you can do approximate then define them to a dimension or parallel,...
  18. Replies
    25
    Views
    2,882

    I think he pulled that one out of you know where...

    I think he pulled that one out of you know where they are called trusses there are several designs out there here is one.

    Warren Truss | Garrett's Bridges

    The crane will have to be designed by...
  19. Replies
    4
    Views
    886

    I don't think its a spirolox as they usually go...

    I don't think its a spirolox as they usually go around more than once, used in piston gudgeon pin holes.

    I have a tool that does snap rings it has a knurl pattern on the outside of the jaws and...
  20. Replies
    9
    Views
    1,227

    The sheetmetal area lets you fold and unfold etc...

    The sheetmetal area lets you fold and unfold etc to give shapes both in folded state and unfolded state, just learning it now.
    Have not seen any expanded metal function i suspect you would need to...
  21. Replies
    67
    Views
    4,255

    as you say the bearing number is only one and as...

    as you say the bearing number is only one and as i don't know the bearing numbers off my head i think your talking about a ball bearing as tapered roller have two numbers one for the bearing one for...
  22. Replies
    8
    Views
    1,314

    get a different mic would be the most logical...

    get a different mic would be the most logical solution the one with the vee anvil it locates on 3 points. two on the anvil and one on the spindle.
  23. Replies
    26
    Views
    2,138

    I have used colchester lathes while i was at tafe...

    I have used colchester lathes while i was at tafe they have both metric and imperial cutting capabilities but i have used a better lathe once you use a better lathe you really don't want to go back....
  24. I thought of something else if you go around the...

    I thought of something else if you go around the workshop for a while in firearms man and get bored with it you could possibly upskill to design work in the same industry and get off the shop floor...
  25. most likely the firearms manufacturer will make...

    most likely the firearms manufacturer will make repeat parts but if you move around the factory you will learn to make the various parts and as they are volume you can get good at hitting the...
Results 1 to 25 of 585
Page 1 of 24 1 2 3 4