Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Hazzert

Page 1 of 50 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    17
    Views
    508

    How many parts are you trying to fit on a fixture?

    How many parts are you trying to fit on a fixture?
  2. Replies
    17
    Views
    508

    I don't have direct experience but I don't like...

    I don't have direct experience but I don't like this plan. A sawcut edge sitting in a pocket with only one contact point on either side of the stock (one pitbull and the pocket) while you profile it?...
  3. Replies
    18
    Views
    668

    Little ironic don't you think?

    Little ironic don't you think?
  4. Replies
    76
    Views
    5,175

    It’s based on your budget, presumably you’re not...

    It’s based on your budget, presumably you’re not making parts that go to space and have had success with a Haas so why jump off the deep end with more machine than you need?

    We have an Okuma...
  5. The worst I’ve seen was a fuel cell compression...

    The worst I’ve seen was a fuel cell compression plate, roughly 20” lo g dog bone shaped with 3d surfaced ports. Pretty much the only tolerances on the part were various profile tolerance GDT callouts...
  6. Replies
    76
    Views
    5,175

    It’s pretty hard to beat something like a...

    It’s pretty hard to beat something like a VF/VM3SS considering your budget. Hell you can get into a UMC750 for about $145k with a 12k spindle.

    I’m not a big Haas fanboy but with them you’d have...
  7. Replies
    43
    Views
    2,561

    That sounds like most modern consumer goods. ...

    That sounds like most modern consumer goods.

    You said that you found hundreds of defects upon inspection. What percentage of previous production would you estimate had (has?) the fault? And if...
  8. Replies
    14
    Views
    1,111

    What kind of stone? I assume carbide would cut...

    What kind of stone?

    I assume carbide would cut most stones to some degree but any inclusions would spell quick death for carbide tooling.

    Maybe look at some cheap diamond points from China or...
  9. Replies
    25
    Views
    2,195

    This is just one of the homegamers that watches...

    This is just one of the homegamers that watches AvEs videos trying to say $700 CAD. It's endearing when he does it and confusing without any of the charm or charisma.
  10. Point your pointer finger to the left and stick...

    Point your pointer finger to the left and stick your thumb straight up so you have a little right triangle. Set it up so that the tip of your finger is the angle you want to find.

    Your thumb is...
  11. How so? Mag base indicators have arms for a...

    How so? Mag base indicators have arms for a reason.

    You can use ether a Tan (opposite and adjacent) trig function


    Tanθ=opposite/adjacent

    θ=arctan(2nd function tan) x opposite/adjacent
  12. Replies
    29
    Views
    2,221

    I think you’re looking at a PCD insert, on the...

    I think you’re looking at a PCD insert, on the bright side if you don’t crash it it should last you quite a while.

    Wind it up as fast as she’ll go you’ll probably break a chip too.
  13. Replies
    5
    Views
    934

    No. Presumably the table is flat(ish) so it’s...

    No.

    Presumably the table is flat(ish) so it’s wear in your ways or saddle etc. Facing the table is only going to provide a perpendicular axis at the position the table was fly cut at. Sounds like...
  14. Replies
    23
    Views
    1,515

    It looks like all those amazon links are...

    It looks like all those amazon links are affiliate links. If anyone were to follow one regardless of what was bought the postee would receive a cut of all the sales made by the clickee for a set...
  15. Replies
    18
    Views
    1,323

    No direct experience but I feel that unless you...

    No direct experience but I feel that unless you were to relieve the side of the wheel to reduce contact you’re more likely to scorch the face plate and should use the periphery of the wheel instead.
  16. Replies
    56
    Views
    4,718

    “Your scientists were so preoccupied with whether...

    “Your scientists were so preoccupied with whether or not they could, they didn’t stop to think if they should.”
    Yeah it’s a curiosity to most but it’s stimulated more interesting content than most...
  17. Replies
    56
    Views
    4,718

    Wire EDM is probably the most economical way of...

    Wire EDM is probably the most economical way of producing an accurate version and would not be particularly limited to width (depth) or material hardness.

    If you just wanted a desktop widget any...
  18. Replies
    6
    Views
    521

    If BobCAD was smart it would calculate the thread...

    If BobCAD was smart it would calculate the thread height for you based on the thread standard selected by the programmer.

    If you are stuck, look up any 20 TPI thread in its library. The value will...
  19. Replies
    29
    Views
    2,099

    You could have wrote it by hand by now and had it...

    You could have wrote it by hand by now and had it to exactly what you wanted.

    Haas has some extra variables on drill cycles but like Mtn said, what machine?
  20. Interesting... I personally use...

    Interesting... I personally use https://www.mscdirect.com/product/details/62691613 and no wrench is included.

    I don't mind pocketing the $300 difference for the lack of wrench and 4mm reduced...
  21. Out of curiosity are they metric or imperial? I...

    Out of curiosity are they metric or imperial? I know there are some omissions on some imperial tooling like the limit markets on their dial indicators.
  22. I don't use it often but the duplicate and rotate...

    I don't use it often but the duplicate and rotate should be set to 1 less than the total desired number of instances since you've already cut one IIRC.
  23. I have never heard of nor seen that disc in any...

    I have never heard of nor seen that disc in any of the full or basic Mitutoyo indicator sets I've bought.
  24. They look similar to a regular scroll chuck...

    They look similar to a regular scroll chuck however like a hydraulic they have limited clamping distance before needing to be reset on the next tooth or step. I am not sure what they excel at.
  25. Replies
    34
    Views
    2,090

    What is wrong with a v-notched grinding vice or...

    What is wrong with a v-notched grinding vice or v-block exactly? I am sure the OP isn't planning on just plopping the barrel down on the chuck.
Results 1 to 25 of 1246
Page 1 of 50 1 2 3 4