Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: 1953chevB

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    25
    Views
    965

    you may want to look at three drills instead of...

    you may want to look at three drills instead of one
    use three drills, 2 shorter drills and a long drill
  2. Replies
    25
    Views
    965

    Please advise what is to be welded at the end of...

    Please advise what is to be welded at the end of the tubing? what is material of end piece?
    does it need to be hollow to get core samples?
    you can actually machine a cutting teeth at the end of...
  3. Replies
    50
    Views
    1,464

    agreed please make positive comments lets stop...

    agreed please make positive comments lets stop being like that
  4. Replies
    10
    Views
    413

    what is the pressure angle of the gear you want...

    what is the pressure angle of the gear you want to make, don't guess
    or cut a gear and roll it with an existing gear if rolls good then your good.
  5. Replies
    10
    Views
    413

    Newer gears cutters are Identified, as John said...

    Newer gears cutters are Identified, as John said older gear depending were and when made....
  6. Replies
    10
    Views
    413

    who did you purchase the cutter from? it should...

    who did you purchase the cutter from?
    it should of been marked DP,PA & WD (D+F) which pressure angle do you require?
    is it in fact what you need?
  7. Replies
    6
    Views
    335

    actually to California prices $500 bucks is not...

    actually to California prices $500 bucks is not bad, you would get sticker shock here, Try Bodycote's near by facilities, there is a ton of suppliers out there.
    if all fails try Certified Metal...
  8. Timken Manual Recommended fits...

    Timken Manual Recommended fits
    https://www.timken.com/resources/timken-engineering-manual/
  9. Replies
    22
    Views
    1,020

    if using blast or buffing it's time consuming...

    if using blast or buffing it's time consuming
    here is a buffing video by eastwood
    How-to & Buffing Basics Demonstration with Eastwood - YouTube
  10. Replies
    20
    Views
    1,237

    would be possible to rough out and then heat...

    would be possible to rough out and then heat treat, leave .250 stock then finish it. inside diameters are tough.
    even rough blanks can be distorted bad, but racking flat, or hang in a free state,...
  11. Replies
    22
    Views
    1,020

    only for stainless it will have adverse effects,...

    only for stainless it will have adverse effects, chem. etch may be viable
  12. Replies
    22
    Views
    1,020

    yes it's called vapor blast, it only cleans

    yes it's called vapor blast, it only cleans
  13. Replies
    22
    Views
    1,020

    it has been my experience it try to prevent it as...

    it has been my experience it try to prevent it as much as possible than to fix it.
    usually with type of product it was best to hand buff, with uncontaminated wheels for buffing.
  14. Replies
    20
    Views
    1,237

    part is solid and no hollow areas? no small holes...

    part is solid and no hollow areas? no small holes or center drills?
  15. Replies
    20
    Views
    1,237

    very slow going, turn and mill?

    very slow going, turn and mill?
  16. Replies
    143
    Views
    4,505

    and since you brought it to attention, what about...

    and since you brought it to attention, what about Sleepy Joe and his escapades, grouping women and little girls on national tv, and for god sakes what was Bill Clinton doing at Epstein's Island, with...
  17. Replies
    143
    Views
    4,505

    so that makes it OK for Jo and Hunter to sell us...

    so that makes it OK for Jo and Hunter to sell us out to the Chinese, as my article above.
    or any other long term politician, why are they not in jail for that, or Obama, Joe and Hilarity and gang...
  18. Replies
    143
    Views
    4,505

    real news The Epoch Times - Truth & Tradition....

    real news
    The Epoch Times - Truth & Tradition. Fact Based. Unbiased. Accurate News
  19. Replies
    143
    Views
    4,505

    fake news main stream media, the leftist tool AG...

    fake news main stream media, the leftist tool
    AG Barr decries the mainstream media as 'a collection of liars' | Just The News
  20. Replies
    143
    Views
    4,505

    how the Bidens got rich ‘Riding the Dragon’...

    how the Bidens got rich
    ‘Riding the Dragon’ documentary alleges Biden family self-enrichment from China | Just The News
  21. Replies
    143
    Views
    4,505

    more scandalize actions by Senate chairman asks...

    more scandalize actions by
    Senate chairman asks DOJ watchdog to open probe into wiped Mueller phones | Just The News
  22. Replies
    143
    Views
    4,505

    In Australia AWESOME moment in Melbourne… –...

    In Australia
    AWESOME moment in Melbourne… – CITIZEN FREE PRESS
  23. Replies
    143
    Views
    4,505

    all lives matter, cops ambushed in LA Compton...

    all lives matter, cops ambushed in LA
    Compton Police Ambush — Officers Still Alive – CITIZEN FREE PRESS
  24. Replies
    143
    Views
    4,505

    more fake news, quit watching this crap

    more fake news, quit watching this crap
  25. Replies
    143
    Views
    4,505

    all fake news

    all fake news
Results 1 to 25 of 460
Page 1 of 19 1 2 3 4