Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter.

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. I have one on mine. It locates the tail of the...

    I have one on mine. It locates the tail of the machine into a hole in the storage box, otherwise it serves no use except as something to keep an eye on as it tends to work loose and fall out.

    I'll...
  2. What is this part that someone would want to...

    What is this part that someone would want to specify such a thread in it?
  3. Replies
    15
    Views
    937

    I just cut felt wipers for my surface grinder...

    I just cut felt wipers for my surface grinder from this:

    Felt Furniture Pads FJSM 1 Roll Felt Floor Protector Pad Felt Tape Self Adhesive Furniture Pad Sticky Felt Pads Heavy Duty Thick Felt...
  4. Replies
    14
    Views
    931

    I made one a couple of weeks ago from 95 shore...

    I made one a couple of weeks ago from 95 shore rubber. Had 3 failed attempts at cutting one out with a hacksaw so I cut one over-sized and ground the sides flat on my bench grinder.

    I didn't think...
  5. That's why I put the description in the post, so...

    That's why I put the description in the post, so people could google them.

    CARBON BRUSHES for Narex: ESV, ESO10, EV 108D, EV406, EV408, EV410, EV710 E126: Amazon.co.uk: Car & Motorbike
  6. The Metabo Jigsaw motor internals ST EP 564/565...

    The Metabo Jigsaw motor internals ST EP 564/565 fit perfectly. They come up all the time on eBay. If you're lucky enough to find the model without the top handle I do believe it's a direct fit...
  7. Brushes: Blue Biax brushes -...

    Brushes: Blue Biax brushes -

    Speed control: Retro-fit speed control to old Biax 7 EL

    Can't help with the brush caps but as I said I would just make them, they are a simple part.
  8. 'Ang on I have a source for brushes. I'm sure......

    'Ang on I have a source for brushes. I'm sure...

    BTW John you can make that 7EL vari-speed by removing the switch and robbing the speed control from a £20 Aldi/Lidl grinder - plus you get the...
  9. Replies
    4
    Views
    456

    I think your crunchy action is more likely to be...

    I think your crunchy action is more likely to be the thrust bearing. Since your machine is a copy of the 10EE you should find the support block and bearings at the far end of the screw.
    The front...
  10. Replies
    4
    Views
    387

    I believe I made mine from a M10 socket cap. 12.9...

    I believe I made mine from a M10 socket cap. 12.9 grade (similar to your 'grade 8' I think). Had to turn down the head a bit and make sure you find one with a long enough shoulder.

    Check the base...
  11. Eagle grinder spindle and way lube? What would you do?

    I'm rebuilding a small manual grinder - an Eagle Mk3 W. Got nearly all of the scraping work done and I'm looking for advice on a couple of bits.

    Despite sitting under a tarp for 10 years the...
  12. Replies
    9
    Views
    816

    Nice follow-up Bill. BTW I have a couple of...

    Nice follow-up Bill.

    BTW I have a couple of spare braking resistors salvaged from a lift motor control if you ever need one. I have one of them fitted in my HLV cabinet for braking with the vfd.
  13. My step chuck body has no markings but my drive...

    My step chuck body has no markings but my drive plate carries the serial EE 2597
  14. Replies
    5
    Views
    774

    I think that's great Mark. Well done for sticking...

    I think that's great Mark. Well done for sticking with it after 5 failed castings too.
  15. As above the bolt clamps the taper attachment...

    As above the bolt clamps the taper attachment bar, the recessed socket cap holds the cross slide nut and the recessed slotted head is the backlash adjuster for the cross slide nut.
  16. Replies
    557
    Views
    92,170

    Thanks Rich yes the whole groove is land-locked...

    Thanks Rich yes the whole groove is land-locked so I'll just scrape over it. The adjacent bolt-on gib also had similar damage but I milled it out then scraped that flat.
  17. Replies
    557
    Views
    92,170

    Currently working on a Eagle surface grinder. I...

    Currently working on a Eagle surface grinder. I got the knee scraped in, here's the z-axis way on the knee.

    273550

    Y axis is pretty good too little bit more to do on it but the bearing is good...
  18. Replies
    11
    Views
    999

    You might want to try Cannon engineering...

    You might want to try Cannon engineering in Leeds they do gear cutting. The owner knows a bit about automotive gears as he's a top fuel bike racer.
  19. Replies
    21
    Views
    5,272

    Check the lines, my cross-slide feed lines were...

    Check the lines, my cross-slide feed lines were plugged up solid.
  20. I have thinned canode with ordinary tap water -...

    I have thinned canode with ordinary tap water - just a few drops in the 1.5ox bottle. It caused no issues. The yellow ink had thickened over a couple of years.
  21. Replies
    6
    Views
    671

    I agree, that one is half-inch taller from the...

    I agree, that one is half-inch taller from the bottom flat to the split than my round-dial steady. Mine is 6.25"
  22. Rich, I don't know what to say, I'm very touched....

    Rich, I don't know what to say, I'm very touched. Thank you.
  23. I had spoken to Jan Sverre about this at the...

    I had spoken to Jan Sverre about this at the time, and he had told me about having to roll out the Canode to use it. This is not the same problem - I mean, I HOPE it is because that would mean I...
  24. This lot was made by B.B. Chemical Corp,...

    This lot was made by B.B. Chemical Corp, LaGrange, Illinois Rich.
  25. I use ordinary brake cleaner with blue paper...

    I use ordinary brake cleaner with blue paper towel. I behaves like any other oil-based spotting dye but the colour is very deep.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4