Search:

ksimolo · 03-02-2021, 09:54 PM

I have some Hardinge and a set of Shars which come in handy when I need an "unusual" size. The Shars I have are of reasonable quality.

ksimolo · 02-26-2021, 02:55 PM

I am tempted to offer to ship it for a mere $4200 :)

ksimolo · 02-21-2021, 11:14 PM

We used to ban contacts under safety glasses if someone was using chemicals. Seems to make sense. Chemicals get under the contacts and you can not get them out. Then a study was actually done and,...

ksimolo · 02-17-2021, 02:33 PM

PM being sent

ksimolo · 02-09-2021, 05:09 PM

PM sent.

Ken

ksimolo · 02-02-2021, 12:44 AM

If you have any left, I would like them.

Thanks,

Ken

ksimolo · 01-29-2021, 09:32 PM

That certainly violates listing rules at some places. I make it a point not to buy from people who do that even if it is a good deal. When it is not an item I want, they are wasting my time...

ksimolo · 01-24-2021, 11:46 PM

I would like both. Sending PM. Thanks.

ksimolo · 01-22-2021, 12:13 AM

I have seen others but here is a result from a quick search:

Inside micrometer - 371 - Feinmess Suhl GmbH - analog

ksimolo · 01-21-2021, 11:34 PM

There are inside thread micrometers but making the go-gauge as mentioned is what makes sense.

Ken

ksimolo · 01-17-2021, 01:57 AM

Found your diagram online - it has two similar looking nuts and a pin so different than my diagram. Found a picture of mine and it looks like mine might be more like your diagram.

310821

But...

ksimolo · 01-16-2021, 11:41 PM

You might find this post useful:

https://www.practicalmachinist.com/vb/south-bend-lathes/using-lever-collet-closer-195227/?highlight=lever+collet+closer

Ken

ksimolo · 01-16-2021, 11:36 PM

Here is a better image.

Ken

310820

ksimolo · 01-16-2021, 11:31 PM

Here are the pages from my parts manual.

Ken

310818 310819

ksimolo · 01-16-2021, 09:08 PM

We do understand the question if you really mean the "stop nut" per the SB parts diagram (item #6 on my parts diagram). In the parts diagram, it does show one set screw (#28) that it calls the "stop...

ksimolo · 01-15-2021, 09:37 AM

I looked at the parts diagram. That is the nut you adjust for each size stock as already mentioned above.

Ken

ksimolo · 12-20-2020, 02:10 AM

Seems like a great deal if in good shape - wish it was closer.

ksimolo · 12-16-2020, 08:15 PM

I also have a Takagi that has worked well for 10 years or more. The major negative with a tankless water heater is that you need a flow of around 1/4 gallon per minute to get them to turn on. If...

ksimolo · 11-30-2020, 10:41 PM

The compressor is fine - it is meant to hold that. But you may want to make sure it is turned off (breaker switched to off if there is no switch at the compressor. No use wasting electricity.

I...

ksimolo · 11-08-2020, 01:19 AM

Received my pumps this week - Thanks!

Ken

ksimolo · 11-06-2020, 10:40 PM

I am interested - sending PM

Thanks,

Ken

ksimolo · 11-04-2020, 10:23 PM

The insulated Roll-Up doors are recommended because they seal much tighter than conventional overhead doors. It is not uncommon to have more heat etc lost due to air leakage than through the...

ksimolo · 10-22-2020, 09:29 PM

I will take 3 groups of 2 motors that you listed.

Ken

ksimolo · 10-22-2020, 12:45 AM

Actually, I would be happy to take it all for the $220.

Ken

ksimolo · 10-21-2020, 11:05 PM

I would be happy to take the tig consumables for the $115.

Search:

Search: Search took 0.00 seconds.

Thread: R8 Collet set for Bridgeport

Thread: Boice-Crane heavy 24” scroll saw

Thread: Is it generally agreed that safety glasses are a must on the lathe and mill?

Thread: Reduced shank Drill bits--FOR SALE

Thread: Excellent Condition Bison 6", 6-jaw Set-Tru Chuck, 1-1/2 - 8 Backing Plate

Thread: Alcoa Mic-6 1/4 X 4.3 X 14

Thread: Using Ecommerce platform instead of eBay to Sell excess machines and Parts????

Thread: For Sale - ISCAR .750 Diameter Insert Tool

Thread: Asking for Some Advice/Help SB Heavy 10 Threading

Thread: Asking for Some Advice/Help SB Heavy 10 Threading

Thread: South Bend lever collet closer

Thread: South Bend lever collet closer

Thread: South Bend lever collet closer

Thread: South Bend lever collet closer

Thread: South Bend lever collet closer

Thread: South Bend lever collet closer

Thread: Kent KGS-250 AHD hydraulic surface grinder

Thread: O/T: Who makes a good gas water heater these days?

Thread: HELP Need--Inherited Machine Shop Tools

Thread: Hydraulic drive motors (small, medium, large)

Thread: FS Simonds A8 4/6 Sawblade Pack of 3

Thread: Metal building insulation options

Thread: Hydraulic drive motors (small, medium, large)

Thread: Large Lots of welding... Tig Mig torches Consumbles

Thread: Large Lots of welding... Tig Mig torches Consumbles