Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: bsg

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Thread: For Sale ! ! !

    by bsg
    Replies
    540
    Views
    261,849

    Sticky: This item is sold! Thanks again Jacques! Kevin

    This item is sold!
    Thanks again Jacques!

    Kevin
  2. Thread: For Sale ! ! !

    by bsg
    Replies
    540
    Views
    261,849

    Sticky: Deckel indexing attachment tailstock FS! This...

    Deckel indexing attachment tailstock FS!

    This is surplus to my needs.
    The only thing wrong with it is the handle peg is loose.....here are some pic's, I can get more if needed?...
  3. Last but not least!...

    Last but not least!
    293986293987293988293989293990
    I'm willing to separate the two attachments if someone is interested?

    One other thing I noticed with the shaping attachment, you move the lever...
  4. And some more! 293981293982293983293984293985

    And some more!
    293981293982293983293984293985
  5. Some better pictures!...

    Some better pictures!
    293976293977293978293979293980
  6. I replied to your email...... Here's some...

    I replied to your email......


    Here's some pictures!

    293761293762293764293765293766

    One other thing about the slotting attachment, it could be adapted to a Bridgeport or similar machine?
    ...
  7. Replies
    2
    Views
    214

    You should remove the front table to balance the...

    You should remove the front table to balance the load, then the covers that are on top of the machine need to be removed to access the upper casting, there are cross pieces you can snake a sling...
  8. Replies
    4
    Views
    509

    These are probably Challenge plates, there were...

    These are probably Challenge plates, there were tons of them before scrap went to $500 a ton years ago!
    They are not for portage layout machines, IIRC, these have the tapped holes on the end for...
  9. Replies
    11
    Views
    844

    I will have a look.....more than likely it will...

    I will have a look.....more than likely it will be built just for the table, everything else I have in the shop has it's own lifting bracket or hook!

    Kevin
  10. Replies
    4
    Views
    509

    Steel/Cast layout tables FS.

    I know of a couple of large steel/cast tables available, I don't know if these have any value anymore or do people just turn them into welding tables now?
    IIRC, one table is 3' x 4' and the other is...
  11. K&T 2D Rotary Cherrying and slotting attachment FS!

    I'm unlikely to ever get one of these machines so I might as well sell these two items?
    I would like to sell them both together, I asking $875 for the pair?

    Let me know if there is any interest,...
  12. Replies
    11
    Views
    844

    After looking at the table and thinking about it...

    After looking at the table and thinking about it a bit, I'm going to fab a bracket and hook arrangement that can be bolted to the table for safe lifting!

    Kevin
  13. Replies
    11
    Views
    844

    I will keep that in mind next time I need to move...

    I will keep that in mind next time I need to move it, it didn't look like it shifted?

    Also, I'm going to call Suburban and try and get a manual/parts diagram and will ask about mag strength, maybe...
  14. Replies
    11
    Views
    844

    Yeah, that's what we did.....we also only raised...

    Yeah, that's what we did.....we also only raised it high enough to transport, then raised it to where it was needed!

    Kevin
  15. Replies
    11
    Views
    844

    I picked this sine plate up yesterday, I used a...

    I picked this sine plate up yesterday, I used a 6" square plate with an eyebolt, the force of the magnet was enough for lifting!

    Thanks for the replies.....

    Kevin
  16. Replies
    11
    Views
    844

    I should have said, this is going on a surface...

    I should have said, this is going on a surface grinder.....I would rather use an overhead method, that's why the question on the magnet strength?

    Kevin
  17. Replies
    11
    Views
    844

    Magnetic chuck strength?

    I bought a 12" x 12" x 6" Suburban compound magnetic sine plate, weighs around 200 + lbs.?
    My question, can I use the magnet to hold a steel plate with a swivel eyebolt to be able to pick this up,...
  18. Replies
    13
    Views
    1,253

    Okay, I stand corrected! I have never seen one in...

    Okay, I stand corrected! I have never seen one in person.....



    My link above has pictures of the setup;

    292289

    Kevin
  19. Replies
    13
    Views
    1,253

    I’m pretty sure that’s for a manufacturing lathe!...

    I’m pretty sure that’s for a manufacturing lathe!

    The cover is bolted on and the upper section is in two pieces, the flat section on top is for the pneumatic control of the closer, not a manual...
  20. Replies
    13
    Views
    1,253

    That end cover came off a manufacturing model...

    That end cover came off a manufacturing model lathe?
    Here’s a link to one discussed here awhile ago with pictures of the collet closer......

    10EE Manufacturing/Turret Lathe

    I would think you...
  21. Thread: M&M spin tables.

    by bsg
    Replies
    4
    Views
    633

    I found this one as well! ...

    I found this one as well!

    http://www.tzsupplies.com/m-and-m-10-roto-grind-precision-rotary-i3746182/

    Kevin
  22. Thread: M&M spin tables.

    by bsg
    Replies
    4
    Views
    633

    Here's another option; ...

    Here's another option;

    https://www.roto-techinc.com/rotary-tables.html

    These show up on the used market from time to time.

    Good luck!

    Kevin
  23. That’s normal, the trailer will pivot on one set...

    That’s normal, the trailer will pivot on one set of axles and scrub the other depending on how it’s configured?
    You should see a triple axle, it pivots on the center and the other two axles scrub in...
  24. Replies
    42
    Views
    4,723

    Was that the machine that was auctioned in...

    Was that the machine that was auctioned in Lapeer? I was going to bid, but I decided to pass as I didn't have a chance to inspect it or if they had a way to load? BTW, if it was that auction, the...
  25. Yes, it's the first page in the Intuitive...

    Yes, it's the first page in the Intuitive Programming System.

    The only time I use it on our TL2 lathe, oddball tools for a one off part, don't have a use for it on the mill!

    On your mill, If...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4