Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: woodchuckNJ

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. so lets blame the dems... but it was this...

    so lets blame the dems...
    but it was this statement that kind of says a lot.

    “In this case, final permits were never issued by the Department of Environmental Protection or the Allegheny County...
  2. Replies
    23
    Views
    36,409

    agreed, vinegar or any acid will eat away at the...

    agreed, vinegar or any acid will eat away at the metal and cause hydrogen embrittlement. it makes the metal rough if in too long. if in short it will remove rust, but make sure you remove it and...
  3. Replies
    23
    Views
    36,409

    if you have a power washer, put some water and...

    if you have a power washer, put some water and detergent in the gas tank.. then use the high pressure washer to scour the inside as much as possible.
  4. Replies
    34
    Views
    1,082

    I always think that too when I see people mount...

    I always think that too when I see people mount them to the ground at 3 feet, just make them work as a covered area
  5. Replies
    55
    Views
    2,533

    my maglite sits idle w/o batteries. I got tired...

    my maglite sits idle w/o batteries. I got tired of putting them in there. 3D cell w/krypton, then changed to led.
    Total crap compared to more modern LED's.

    my double AA cell unit also sucks...
  6. Replies
    32
    Views
    1,223

    nah, just get a small charcoal bbq, get the...

    nah, just get a small charcoal bbq, get the charcoal hot put it in there, keep it hot..
    tig it,
    put it back in and keep it hot for a while, then let it cool off on it's own.
  7. find a blacksmith.. gotta be one in the area.

    find a blacksmith.. gotta be one in the area.
  8. Replies
    32
    Views
    1,223

    Hell no... we are machinists right? Repair...

    Hell no... we are machinists right? Repair...
  9. Replies
    32
    Views
    1,223

    copper does not weld, I don't know about brazing...

    copper does not weld, I don't know about brazing with bronze, but generally I use copper to back up a weld that I need to protect.
  10. I don't know the spec for the Lambo, but I...

    I don't know the spec for the Lambo, but I suspect that's too tight. That would heat up and seize in my unknowledgeable opinion from out my ass.
  11. Replies
    52
    Views
    2,090

    Yea, I like it too, looks like an 8 foot bed,...

    Yea, I like it too, looks like an 8 foot bed, can't stand those 6 foot beds, what am I going to haul with only 6'
    can't get plywood/sheetrock in there, it has to be raised on the tailgate.
  12. Replies
    52
    Views
    2,090

    I have to hijack this superduty thread, since...

    I have to hijack this superduty thread, since it's ford related.

    Have any of you seen the new electric mustang? Not even a mustang, it looks like an SUV.. WTF are they thinking over at ford......
  13. Replies
    52
    Views
    2,090

    or the super wide deep dish wheels , but the...

    or the super wide deep dish wheels , but the spindles and are really not prepared to handle the super wide offset, and the bearings keep failing..

    In the middle of the night hearing one of the...
  14. Replies
    52
    Views
    2,090

    I hate shoveling into a jacked up new truck. ...

    I hate shoveling into a jacked up new truck. When I have to do that I wish I had a front loader.

    Trucks are stupid high these days. And stupid short beds.. Try to get a regular cab, with a full...
  15. Replies
    52
    Views
    2,090

    who hit who? looks like you got hit by the other...

    who hit who? looks like you got hit by the other driver.

    So their insurance will pay you to have it fixed.

    So just get it fixed.

    I think you are more interested in modifying the truck you...
  16. Replies
    55
    Views
    2,533

    try this link Rechargeable Flashlights...

    try this link
    Rechargeable Flashlights

    The button is where it should be, it turns on to the setting you left it.
    it can be low, or super bright... and in-between.
  17. Replies
    52
    Views
    2,090

    neither of those vehicles is totaled. Fix the...

    neither of those vehicles is totaled.

    Fix the rocker panel and pillar if damaged. It doesn't look like the damage hit the pillar imho.

    That does not look like much damage, not at all. Your...
  18. So very true about old quality. Usually it just...

    So very true about old quality. Usually it just needs a touch up with a stone, OR some machining to fix wear, then shimming or replacing some worn out parts.

    A low quality chineese vise can be...
  19. Replies
    57
    Views
    3,257

    yea, we've all had those moments I think. I...

    yea, we've all had those moments I think. I remember my dad embarassing the hell out of me with plaid pants, and with white pants.

    BUT BACK TO THE optivisor, who cares when you are working on...
  20. Replies
    57
    Views
    3,257

    why ? is the looks important? from what I know...

    why ? is the looks important?

    from what I know the visor is very light weight. I think that's why they don't do all this plastic injection molding that makes it heavier and brittle.

    I'm not a...
  21. Replies
    57
    Views
    3,257

    I went with 3.0 reading glasses. Don't laugh,...

    I went with 3.0 reading glasses. Don't laugh, they are great. Light weight, economical, for me they were much better than working under a lighted magnifier.

    it's not for everyone, but for $20,...
  22. PHOTO of the unit and ceramic brick. or link...

    PHOTO of the unit and ceramic brick.

    or link to the product you bought...
  23. Replies
    72
    Views
    5,826

    So then you seem to support NO JOY... Thinking...

    So then you seem to support NO JOY...
    Thinking he did a great job??? WTF.. the man dismantled all the machines, not just shut them. Its not a problem of all packages, its still a letter problem...
  24. sounds ridiculous that you need to be involved...

    sounds ridiculous that you need to be involved that way.
    this sounds like a small furnace...

    you shouldn't need to dick around with a block to seal it.. unless it's an open long type furnace.....
  25. Thread: Die filer

    by woodchuckNJ
    Replies
    31
    Views
    2,145

    I have a dewalt scroll saw 788. And it would...

    I have a dewalt scroll saw 788. And it would easily do the job, you would have to take some files and ground some flats on them so that the clamps can hold them. They also sell carbide grit files .....
Results 1 to 25 of 302
Page 1 of 13 1 2 3 4