Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Personnally I would buy one Din 6303 About...

    Personnally I would buy one Din 6303
    About €2,50 or less at Kipp
    I order there on a regular base anyhow
    Not a exact copy but it works and looks good

    Peter
  2. Can you clamp it lenghtwise ?? Works better...

    Can you clamp it lenghtwise ?? Works better probably


    Peter
  3. Perhaps the electromagnetic clutch is bad First...

    Perhaps the electromagnetic clutch is bad
    First check for conductivity
    Then see if it gets the right voltage and if it is AC or DC
    If that is oke perhaps the gap is too big Try to set it...
  4. You should inspect not only the spindle But the...

    You should inspect not only the spindle But the housing where the bearings seat too
    Roundness ecspecially On old machines I never found a housing that was to specs Well At least the few times I...
  5. Do not make them to existing lines then But go...

    Do not make them to existing lines then But go from the first line or a edge

    Peter
  6. Replies
    120
    Views
    88,356

    We do not have 12 fingers though Peter

    We do not have 12 fingers though

    Peter
  7. Yes Looking closer the drawing is completly...

    Yes Looking closer the drawing is completly wrong
    If numbering the triangles clockwise from 1 to 6 starting at 1 0clock
    The triangles 1-3-4-6 need to be recktangles
    No 3 and 4 put together...
  8. Oke How good are you at Dutch :D Symetrical it...

    Oke How good are you at Dutch :D
    Symetrical it is
    Thats my English word for this day then

    Peter
  9. Make it out of 2 pieces Split the drawing in half...

    Make it out of 2 pieces Split the drawing in half That way you have a syncronic model which will form easier and look better
    The 90 dgr bends on the square will be rounded Use a hammer to tap...
  10. Replies
    3
    Views
    321

    Yes Well made machines But that is not unique...

    Yes Well made machines
    But that is not unique to Switserland or Germany

    Peter
  11. Replies
    3
    Views
    321

    They were never made in eighter Switserland or...

    They were never made in eighter Switserland or Germany
    They were imported rebadges Prvomajska ALG 100 made in Zagreb

    Peter
  12. Plain bearings have a lower surface speed as the...

    Plain bearings have a lower surface speed as the balls in a bearing Much lower Deep grove ball bearings that size are in ratio pretty big
    So a plain bearing with even a smaller shaft might do...
  13. Panzergewinde aka PG was the norm here in Europe...

    Panzergewinde aka PG was the norm here in Europe till about 30 years ago
    Here we can still order PG glands locknuts fittings and such
    I have them in stock as that is what is used on the machines...
  14. On my 92 FP1 I see the name PMA-fix That is...

    On my 92 FP1 I see the name PMA-fix
    That is part of ABB now
    They also have a divisable system
    PMA cable protection - Conduit & fittings | ABB
    Peter
  15. Manual in Englisch for a Deckel FP1 2102

    Is there anyone who can guide me to a link where I can download a manual for a Deckel FP1 2102 in Englisch A 2101 would do as well I suppose
    A customer wants one
    I have plenty of them in German ...
  16. I see the pressure angle is a standard 20° On a...

    I see the pressure angle is a standard 20°
    On a working gear you have a rolling component and a rubbing component there were the teeth meet oneanother
    On most handtools and other mass produced...
  17. Can you use a gasspring to counterbalance perhaps...

    Can you use a gasspring to counterbalance perhaps ???

    Peter
  18. Aac blocks are fireproof. Cheap. A bit stronger....

    Aac blocks are fireproof. Cheap. A bit stronger. Easy to get your hands on. Easy to cut to size

    Peter
  19. Just brought mine to bookkeepping Do they have...

    Just brought mine to bookkeepping
    Do they have VAT in Namibia?
  20. Hahaha Love your comments sometimes :D ...

    Hahaha
    Love your comments sometimes :D


    Peter
  21. Tjesis I just pointed you in the right...

    Tjesis
    I just pointed you in the right direction
    What did bite you this morning
  22. FYI Machinery Discussion Guidelines...

    FYI
    Machinery Discussion Guidelines
  23. I disagree with you The moderator on several...

    I disagree with you
    The moderator on several occasions made it very clear this forum is not to discus the chinese hobbymachines On several occasions I have noticed that members made newcommers...
  24. The AXA multifix is the best you can buy right...

    The AXA multifix is the best you can buy right now And reasonably priced also At least if you want a multifix type of toolholder
    The Amestra original multisuisse are comparable quality but more...
  25. That is the nice thing about Deckel Parts are...

    That is the nice thing about Deckel Parts are still available at a affordable price
    BTW a good tool to make your own nut is a tap bought from Aliexpress or Alibaba Price is about 30 euro
    I was...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4