Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rakort

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    346

    There is a "neutral" detent in the middle of the...

    There is a "neutral" detent in the middle of the fwd / rev shift knob travel that you must land on. That is the interlock! I had some troubles with this as well until I got it all cleaned and tuned...
  2. Replies
    6
    Views
    591

    I've asked some questions.....the knobs also...

    I've asked some questions.....the knobs also don't look to be round dial vintage.
  3. Replies
    6
    Views
    591

    Follow Rest - Round Dial?

    Thoughts? I was thinking that this style of follow rest was only for a square dial?


    MONARCH 10EE LATHE ADJUSTABLE FOLLOWING REST 12.5" HEIGHT FOR ROUND DIALS | eBay
  4. Replies
    16
    Views
    747

    as usual I can't sleep long enuff to get through...

    as usual I can't sleep long enuff to get through a threm post....what did he say? can anyone boil it down?
  5. Replies
    16
    Views
    747

    what is it with us riding these motors and mg...

    what is it with us riding these motors and mg sets around on cheap furniture moving dollies!?

    So I happen to have the MG you are looking for. I hate to sell it as it matches my lathe, but its...
  6. Replies
    18
    Views
    1,363

    sigh, life moves on. I'm sure there will be...

    sigh, life moves on. I'm sure there will be plenty interested. Can you post some pixs?
  7. Replies
    30
    Views
    1,441

    use this button.... 318078 then click...

    use this button....

    318078

    then

    click on "from computer" tab

    click on "choose file"
  8. Replies
    4
    Views
    409

    the correct term is oil cup or oil cover Gits...

    the correct term is oil cup or oil cover

    Gits is a big name maker of those. GITS Manufacturing | Leading provider of air flow management solutions

    Most of what I see nowadays is the spring...
  9. Replies
    48
    Views
    2,653

    as many have said, for many reasons, do...

    as many have said, for many reasons, do everything you can do to restore the original drive. You will be much happier in the end.
  10. Replies
    36
    Views
    2,226

    Handling and Installation of a Monarch lathe from...

    Handling and Installation of a Monarch lathe from the Mfg.

    I with Bill though, I like the straps inside the ways, but putting them outside the ways would provide a little more stability (at the...
  11. Replies
    24
    Views
    970

    yup the "exciter" is the generator that is belt...

    yup the "exciter" is the generator that is belt driven ontop of the main motor generator. It provides all the control voltage for all the relays switches and what not including the field voltage as...
  12. Replies
    24
    Views
    970

    You have all the help you need here. Listen to...

    You have all the help you need here. Listen to Cal he is the maestro of MG's and all things EE. There are many others here that will help as well. Do heed the safety comments about poking around...
  13. Replies
    36
    Views
    2,226

    I second or third that! A half an hour with a...

    I second or third that! A half an hour with a tow truck is not that expensive and WELL worth it.

    316712
  14. Replies
    47
    Views
    2,494

    Yeah, that comm looks bad. Maybe it is the...

    Yeah, that comm looks bad. Maybe it is the camera / reflection / lighting, but I wonder if it is too far gone to be undercut? Hopefully there is a lot of meat on there yet. One way to find out,...
  15. I am an engineer and I'm sure a single 3/8" grade...

    I am an engineer and I'm sure a single 3/8" grade 5 bolt will swing in the air a 10EE all day long. NO worries on 5/8" whatever grade you get to hold it to a pallet. I do agree 5/8 is the right...
  16. Replies
    17
    Views
    1,102

    Totally agree with your comments about fitting a...

    Totally agree with your comments about fitting a chuck/back plate to your lathe. It is a right of passage that is fun and satisfying. Yes use the lathe to repair and build your lathe. I saw some...
  17. Replies
    11
    Views
    862

    Make sure you have cleaned out all the old tube...

    Make sure you have cleaned out all the old tube "seating" material out of the tube hole.....I think it was melted sodium originally. That hole was also drilled with 2 different drill operations and...
  18. Replies
    17
    Views
    1,102

    Well, I would like it, but need it is a stretch!...

    Well, I would like it, but need it is a stretch! I was largely kidding. I hope it works out for you. That chuck looked to be in pretty good shape.....little clean up and away ya go! Let us know...
  19. Replies
    17
    Views
    1,102

    dang it, someone bought my chuck!

    dang it, someone bought my chuck!
  20. Replies
    6
    Views
    520

    Good call on the flat vs v-belt. I jumped the...

    Good call on the flat vs v-belt. I jumped the gun assuming we knew we were talking about a flat belt here!

    314549

    I knew this was talked about excessively here already but couldn't dig up the...
  21. Replies
    6
    Views
    520

    I've taken some measurements on my setup. The...

    I've taken some measurements on my setup.

    The upper/spindle sheave is 7.24" dia
    The lower drive sheave is 6.83" dia
    the tensioner sheave is 3.00" dia

    I measured between 87.75" to 88.25" in...
  22. I'll get second on the list for the upper cover...

    I'll get second on the list for the upper cover knob if this doesn't work out!
  23. Replies
    6
    Views
    520

    Spindle Drive Belt 10EE Round Dial

    I've searched poked around and otherwise tried to find some details for a replacement spindle drive belt for my 1943 round dial. I would like to understand what folks have used for replacement...
  24. Replies
    17
    Views
    1,102

    forget that chuck, all day long I would go for...

    forget that chuck, all day long I would go for this one......and I just might. No backplate means more distance "between centers" if you will

    I have the same chuck in a 6" and I love it.
    ...
  25. Replies
    17
    Views
    1,395

    Makes perfect sense to me and well inline with...

    Makes perfect sense to me and well inline with what I was thinking and NEEDED to be. I don't see a snap ring illustrated in the drawing rimcanyon shared so I was assuming there was a setscrew in...
Results 1 to 25 of 453
Page 1 of 19 1 2 3 4