Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jz79

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2,473
    Views
    75,038

    it seems to me that the way those statistics are...

    it seems to me that the way those statistics are gathered leave a lot of variation in regards to the actual situation

    for instance, in countries where testing is widely available, you will get...
  2. Replies
    93
    Views
    28,617

    put a dial indicator in parallel with that axis...

    put a dial indicator in parallel with that axis and zero out the DRO in mid travel of that indicator (adjust the indicator to zero as well), then traverse over the zero mark 10-20 times from lets say...
  3. Replies
    35
    Views
    1,741

    it is very unlikely for such oxidation to be...

    it is very unlikely for such oxidation to be caused by poor grounding, and it is quite easy to check, run a separate ground wire near the machine and use almost any voltmeter (multimeter set on...
  4. Replies
    5
    Views
    657

    hmm, must have missed the nut coming loose part...

    hmm, must have missed the nut coming loose part the first time I red this, or he added that later in edit, because I recall only "normal chips in the wrong direction", which is impossible in CRS with...
  5. Replies
    35
    Views
    1,741

    are you talking about all of the 1 or 2mm of...

    are you talking about all of the 1 or 2mm of exposed copper right below the bare connector?
  6. Replies
    5
    Views
    657

    "fancy angles" have little to do with the "wrong...

    "fancy angles" have little to do with the "wrong way" in this case (which I'm guessing is feed direction, not tool rotation), general construction of the machine and the condition it is in will have...
  7. Replies
    2,473
    Views
    75,038

    there was a report that over half of the infected...

    there was a report that over half of the infected people lost a sense of smell for a while

    I think (again, not a doctor) symptoms and severity of illness greatly depends on where the virus entered...
  8. Replies
    12
    Views
    2,680

    I've seen videos of Mahos and Deckels switching...

    I've seen videos of Mahos and Deckels switching gears and noticed that they seem to "twitch" the motor to help the gears mesh, and that is what surprised me with this machine - there is no spindle...
  9. Replies
    1,051
    Views
    96,715

    the "problem" with brandnamed used (older) tools...

    the "problem" with brandnamed used (older) tools is that they often use slighty non-standard shaped inserts, which might simply not be available any more new

    if I remember correctly, that is why...
  10. Replies
    1,051
    Views
    96,715

    regarding the indexable holders for home shop...

    regarding the indexable holders for home shop use, these seem to work quite well, they definitely need careful deburring of the insert pockets before you fit the inserts, but once that's done, they...
  11. Replies
    12
    Views
    2,680

    I already tried asking around local machine...

    I already tried asking around local machine shops, and it seems that there are only couple offering mostly electronics repairs, no re-grind service unfortunately.
    I googled up few spindle repair...
  12. Replies
    12
    Views
    2,680

    received few din2080 pull studs from Singer a...

    received few din2080 pull studs from Singer a couple days ago, and bought few new holders as well to do some test cuts, and confirmed the suspicion about worn taper in the vertical head, probably due...
  13. Replies
    34
    Views
    2,039

    how about showing how the part was held down?...

    how about showing how the part was held down? that end mill, even with "no geometry", cannot be solely responsible for that result
  14. Replies
    2,473
    Views
    75,038

    I didn't read the whole thing because it is a...

    I didn't read the whole thing because it is a slander article, it is a pile of garbage

    No doctor in their right mind ANYWHERE listens to what Trump has to say about any of this, his press release...
  15. Replies
    2,473
    Views
    75,038

    how is that Trumps fault that they overdose...

    how is that Trumps fault that they overdose patients?

    do those stupid reporters really think that doctors there looked at Trumps press release and pumped the patients full of it thinking it is...
  16. Replies
    2,473
    Views
    75,038

    it seems that the newly infected and asymptomatic...

    it seems that the newly infected and asymptomatic start spreading the virus just couple days before developing first symptoms (fever and cough), so the 10-14 day strict quarantine would weed out...
  17. Replies
    2,473
    Views
    75,038

    I'm actually very impressed with how Japan has...

    I'm actually very impressed with how Japan has handled this, 1100 cases, 41 deaths, oldest country in the world with very high population density...

    and just now (hopefully not due to weekend),...
  18. Replies
    2,473
    Views
    75,038

    a lot of that spike might be people panicking and...

    a lot of that spike might be people panicking and thinking guaranteed social benefits pay while staying at home for next 2-3 months is better than risk of getting seriously ill
  19. Replies
    2,473
    Views
    75,038

    interesting you noted the self medication and...

    interesting you noted the self medication and anti inflammatories, one of the channels I mentioned earlier, the doctor there looked into Spanish flu and aspirin was the new wonder drug at the time,...
  20. Replies
    2,473
    Views
    75,038

    I'm watching these two for news regarding this,...

    I'm watching these two for news regarding this, general media seems pretty useless in this regard :(

    YouTube

    and this explains the mechanics as understood so far
    YouTube
  21. Replies
    2,473
    Views
    75,038

    what puzzles me (as non doctor) is how some are...

    what puzzles me (as non doctor) is how some are apparently hit very hard, yet others in same age group and similar condition get over it with just the fever

    I'm thinking the worse cases were with...
  22. Replies
    23
    Views
    1,145

    what I want to know now is how big is the water...

    what I want to know now is how big is the water bottle and is it mounted to the frame? :D
  23. Replies
    23
    Views
    1,145

    how much weight are you going to save with those...

    how much weight are you going to save with those special M6x15 and M5x10 screws? especially on an off road vehicle...

    m6x15 screw wight in steel is around 6 grams, 2.2 in aluminum and 3.5 in...
  24. Replies
    2,473
    Views
    75,038

    statistics are inconsistent, the only common...

    statistics are inconsistent, the only common thing I know of is that it affects men more than women, that is quite clear, but the age group is very uncertain, at least for now

    the problem with...
  25. Replies
    2,473
    Views
    75,038

    I don't know who comes up with this, but the...

    I don't know who comes up with this, but the person is clearly dumb, there is a world of difference between this thing and the flu, which predominantly is older people problem, if you're healthy...
Results 1 to 25 of 444
Page 1 of 18 1 2 3 4