Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: dana gear

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. I went through all my old Hobart international...

    I went through all my old Hobart international literature, I don't have much on the European stuff , however I could nothing on the RC 166 manufactured in Amsterdam. Question, There was not a Hobart...
  2. My Oldest Monarch CBB is from the late 30's. it...

    My Oldest Monarch CBB is from the late 30's. it has the oil riser type sight tube, although on mine it just threads into the side.
  3. When I was a kid (long time ago) my grandfather...

    When I was a kid (long time ago) my grandfather had several Niles lathes. Monsters, he used the overhead crane to change tooling.
    Two of them the operator would ride on the carriage. Very slow speed...
  4. Replies
    13
    Views
    1,246

    Run hours make sense to a degree, but here's the...

    Run hours make sense to a degree, but here's the rub there, we had two Bridgeports purchased new and the same time.
    One spent it's life in Aluminum only, the other Carbon steel. Both were traded...
  5. Replies
    14
    Views
    726

    For giggles and grins try YRC For some unknown...

    For giggles and grins try YRC For some unknown reason if I don't use my account with them and go on line to YRC.com and use my credit card they have amazing low rates. Big difference between charging...
  6. Where does it state on the machine that it can be...

    Where does it state on the machine that it can be reconfigured for 3 phase input.
    I am far from up to speed on European Hobart, but I don't recall there being a 3 phase option on these.
    It should...
  7. I was a little afraid of that, as I said before...

    I was a little afraid of that, as I said before the 166 is a orphan, As far as I know its been out of production for some time.
    ITW purchased Miller electric and some time after that purchased...
  8. This one was purchased by me from the original...

    This one was purchased by me from the original owner . It came out of a very large lumber processing company that has been in business over 85 years. Management in another part of the state decided...
  9. It would seem that most if not all of the high...

    It would seem that most if not all of the high speed heads tend to weep around the spindle after heating up through usage.
    I have the two and a friend has one they all weep a little bit ,not a lot...
  10. That's odd, Try this then, ITW welding products...

    That's odd, Try this then, ITW welding products BV. Netherlands phone, +31 186 641 444.
    The 166 is a orphan...…………………….
  11. I have 2, k-2 high speed universal milling heads,...

    I have 2, k-2 high speed universal milling heads, one came out of a shop that had it for years and used it relatively often.
    As far as I can tell in all the time they used it was always packed with...
  12. Replies
    12
    Views
    610

    If I am correct, you have a press with single...

    If I am correct, you have a press with single acting rams (hydraulic pressure on one side only) with some means to retract the ram the opposite direction. On single action rams the opposite side of...
  13. Just as e-fishin-c states regardless of the hose...

    Just as e-fishin-c states regardless of the hose I.D. size you use it will still only allow the flow volume of the end fittings you use at a given pressure. As the pressure increases so will flow...
  14. Give this a try, Hobart international...

    Give this a try, Hobart international headquarters, Phone 937-332-5188.
    email: [email protected]
  15. Replies
    12
    Views
    823

    For what's it worth 240 Delta, In my home shop I...

    For what's it worth 240 Delta, In my home shop I installed a 400 amp, 3 phase braker panel for all the 3 phase equipment with a 200 amp master braker pulling off the two non stinger legs in that...
  16. Replies
    13
    Views
    1,246

    Me too, I have seen CNC equipment that looked and...

    Me too, I have seen CNC equipment that looked and operated brand new after 4 years of usage and then there's equipment that looks like it was shit off a Clift at 2 years of usage. just like Dualkit...
  17. We have one here for sharpening flat top punches...

    We have one here for sharpening flat top punches used for stainless, I not sure because it's been some time ago but I thought we paid something like 1,800.00 for it.
  18. Replace the broken gear.

    Replace the broken gear.
  19. Years back we had a new guy that decided to...

    Years back we had a new guy that decided to change the feed rate (much faster) on our monster Cincinnati brickford radial drill press.
    He was drilling a 2.375 hole in 4" thick A-36 plate. blew...
  20. Replies
    3
    Views
    379

    Try this, go to esab web site, Welding Equipment...

    Try this, go to esab web site, Welding Equipment ESAB North America | ESAB Welding & Cutting
    In the search box upper right hand corner type in HDA-200. The entire operators/parts/service manuals is...
  21. Replies
    3
    Views
    694

    As a rule of thumb on our press brakes we adjust...

    As a rule of thumb on our press brakes we adjust for .003 all the way.
    We have done this on our Versons, Chicago and Cincinnati press brakes up to 500 ton capacity.
  22. Replies
    9
    Views
    700

    Now I am a little confused, all your feeds and...

    Now I am a little confused, all your feeds and rapid work correctly. So I would assume your spindle drive is what you are experiencing problems with?
  23. Replies
    13
    Views
    1,392

    I am located in northern California, there...

    I am located in northern California, there appears to be no problem with inventory of Dynasty 400 at Miller on the west coast.
    That said I have operated various models of Miller and Lincoln...
  24. Replies
    4
    Views
    912

    There all great machines, I use to say if you...

    There all great machines, I use to say if you want to see how well something is made see what survives in schools and rental yards.
  25. Just a guess, but we have a large electro-magnet...

    Just a guess, but we have a large electro-magnet for lifting material, some years back we noticed chipping around the coil unit and contacted the manufacturer, there tech guy told us to just reseal...
Results 1 to 25 of 241
Page 1 of 10 1 2 3 4