Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Mr.Green

Search: Search took 0.00 seconds.

  1. Replies
    23
    Views
    2,583

    Let's just saying having him take care of it...

    Let's just saying having him take care of it would have cost me more time and significantly more money.

    I had about 300 bucks total in cylinder repair, new hoses, some exhaust pipe, gasket sheet,...
  2. Replies
    23
    Views
    2,583

    Well that didn't pan out, but found a local...

    Well that didn't pan out, but found a local independent forklift dealer that was able to rebuild it for me. Forklift has never steered this nice

    Sent from my SM-N960U using Tapatalk
  3. Replies
    23
    Views
    2,583

    I found an old timer whom him and his father both...

    I found an old timer whom him and his father both retired from Clark. He is going to rebuild one he has and send it out to me. He told me I could replace the wiper seals on the ram and it would still...
  4. Replies
    23
    Views
    2,583

    I think there is about 6" under this one, I...

    I think there is about 6" under this one, I blocked under the mast and picked up the ass end with my other lift so I could block it.

    About 13k pounds I believe.

    Sent from my SM-N960U using...
  5. Replies
    23
    Views
    2,583

    The only leak I could actually see was from rod...

    The only leak I could actually see was from rod seal end. Everything was filthy under this thing, but a lot of that is from seeping hoses going to this and the PS fluid reservoir leaked like crazy. ...
  6. Replies
    23
    Views
    2,583

    That's great, thank you. Looks like a ton of...

    That's great, thank you. Looks like a ton of seals and packing parts in the ram end.

    I bet my hydraulic shop has all those seals for that end.

    Sent from my SM-N960U using Tapatalk
  7. Replies
    23
    Views
    2,583

    It would probably be in my best interest to just...

    It would probably be in my best interest to just have it rebuilt by my usual shop. They can fix, make, build anything hydraulic related. Great old shop.

    Vickers, thank you.

    Sent from my...
  8. Replies
    23
    Views
    2,583

    My phone won't let me open that link. ...

    My phone won't let me open that link.



    Sent from my SM-N960U using Tapatalk
  9. Replies
    23
    Views
    2,583

    Yes, I believe you are correct. Sent from my...

    Yes, I believe you are correct.

    Sent from my SM-N960U using Tapatalk
  10. Replies
    23
    Views
    2,583

    5 hours later, sacrificed exhaust, completely...

    5 hours later, sacrificed exhaust, completely covered in grease and grime it's out.

    It won't let me upload picture of end of ram, but there is a snap ring that must hold that seal in. I will take...
  11. Replies
    23
    Views
    2,583

    I am planning on pulling it out tomorrow. Figure...

    I am planning on pulling it out tomorrow. Figure I will use every swear word I know before it's out.

    Sent from my SM-N960U using Tapatalk
  12. Replies
    23
    Views
    2,583

    The first picture shows the end that hooks to the...

    The first picture shows the end that hooks to the drag link for the steering, which looks like a typical tie rod end that threads on and clamps. There are 4 bolts right there by where the steering...
  13. Replies
    23
    Views
    2,583

    Actual cylinder, hard to photograph well....

    Actual cylinder, hard to photograph well. https://uploads.tapatalk-cdn.com/20190804/cffaadeb775e02b5c63efab87b9069d5.jpghttps://uploads.tapatalk-cdn.com/20190804/fc729a27c3284f361de52998bd2e0863.jpg...
  14. Replies
    23
    Views
    2,583

    Not sure that is possible. It's not quite a...

    Not sure that is possible.

    It's not quite a typical cylinder, by the time I tried to modify an off the shelf one, I would have way too much time in it.

    It looks pretty close to this:
    ...
  15. Replies
    23
    Views
    2,583

    Clark utilitruc power steering cylinder

    The PS cylinder on my 1963 hut100 clark is pissing fluid out the ram end.

    According to the build sheet I got from clark it says PS cylinder is a 325490.

    It is a welded unit, looks like it has...
Results 1 to 15 of 15