Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: diesel-xj

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. thanks for the schematic. I will have to keep...

    thanks for the schematic. I will have to keep that for later.
    I did evacuate ( run from the storm ) with one good vacuum pump. But my vacuum oven went under water. I guess the vacuum...
  2. Thanks for the encouragement Bill, I will get a...

    Thanks for the encouragement Bill, I will get a report from the motor shop tomorrow. I have no idea what they will say. I did think to try a do a bearing replacement myself. My shop is just...
  3. ok enough said. I think it will be easier to...

    ok enough said. I think it will be easier to just bite the bullet again and go back to 3phase with a little china VFD.
    But I still have a few questions. Is there actually a dedicated...
  4. reviving the dead here a bit. I also have a...

    reviving the dead here a bit. I also have a standard modern 1340 lathe. It only went under salt water for a little while in Hurricane Harvey. The budget on the shop repair is very tight. I...
  5. good morning ripper. last night I had thought...

    good morning ripper. last night I had thought about trying to tap into the top of the broken bit, but your solution sounds much better. repairing from the top does not have near as much good...
  6. Now that I cleaned up a bit and found the broken...

    Now that I cleaned up a bit and found the broken part of the gib I can see the process for the repair. I am still PO'd about the broken x axis bearing cap.
  7. ripper I think the broken part is the notch. ...

    ripper I think the broken part is the notch. there is supposed to be a repair like you suggest for this. I had never paid much attention to the gib , so I don't really know what it looked like...
  8. Lagun Anilam CNC Mill with broken tab on Y axis gib

    Hello. I am working through my Hurricane Harvey salt water flooded shop. A few days ago the Y axis on my old Lagun Anilam CNC machine seized up. it turns out the y axis gib got stuck on some...
  9. a little good news sort of. I don't think my...

    a little good news sort of. I don't think my stuck y axis is the ball screw. I think the gib is jammed up. Of course the end of the gib broke off when I pulled the adjustment screw out, and...
  10. Well we had all types of water here, maybe not so...

    Well we had all types of water here, maybe not so much river water, but I'm sure there was plenty of sewage mixed in. At least the water did not stay up for weeks. I think one thing that may have...
  11. thanks for the reply. I am not too worried...

    thanks for the reply. I am not too worried about the electronics for the CNC. I am planning on doing a control retrofit. I will pull the Anilam boards out and wash them as you said, and then...
  12. Lagun manual & cnc. Finally getting into my hurricane Harvey salt water flooded shop

    I took a direct Hurricane Harvey hit, A little over 6 feet of Gulf of Mexico salt water took out my shop, and house. Yes it has been a long time to get back in the shop, but that is just how it...
  13. Thermo CRS robotics F3 6 axis arm help with CRS software

    hello. I have a new to me 19 year old CRS F3. This is 6 axis arm with a C500C controller. I am looking for a copy of any of the CRS software
    titles are: RAPL-3, Robcomm3, or ActiveRobot.
    ...
  14. Replies
    9
    Views
    2,289

    thanks Adama, yes it is a bit of sheet. will...

    thanks Adama, yes it is a bit of sheet. will read HSM. I am still more interested now about your conversion/retrofit. My servos seem fine. I gotta run now but thanks
  15. Replies
    9
    Views
    2,289

    thanks for the reply's Adama and Doug8. Adama...

    thanks for the reply's Adama and Doug8. Adama I understand you think it best to just drop the cutter all the way thru the 3/8 stock and cut the circle in one pass as opposed to taking small bites...
  16. Replies
    9
    Views
    2,289

    I am getting things worked out slowly. I was...

    I am getting things worked out slowly. I was able to program and cut a circle. the machine is performing just fine. the hole spec'd out at .0005 which is good enough for me.

    I am still...
  17. Replies
    9
    Views
    2,289

    little update. I am still working thru the...

    little update. I am still working thru the factory manual. I am pretty well able to make non complicated moves including arcs. But when I try using canned cycles such as peck drilling and...
  18. Replies
    9
    Views
    2,289

    LAGUN Anilam crusader M getting started

    I have a new to me Lagun Anilam 3 axis mill with a Crusader M control. So far the machine seems to be working well. I am a newb to CNC. I am looking for a G-code programming tutorial.. of some...
  19. nope this one does not have the round mount on...

    nope this one does not have the round mount on the tail for the shaper, my ft-1 has that bit on the tail.

    so can you use this style lagun to copy or trace a part and then make a new one?
  20. yes Snowshooze it is a hard head for the z-axis, ...

    yes Snowshooze it is a hard head for the z-axis, so no head tramming, it does not tilt, but on the column it goes in and out same as the y-axis when straight, and it rotates left and right on the...
  21. that is kind of what I thought on the humidity. ...

    that is kind of what I thought on the humidity. I work overseas a lot, when I get ready to go to work I cover every thing in motor oil or transmission fluid, then cover with oil soaked toweling,...
  22. Thanks for the reply's. The Kiwa Colt 510 has a...

    Thanks for the reply's. The Kiwa Colt 510 has a tool changer. but until I get my new shop built I am very space limited I guess I will end up with the Lagun and the Anilam crusader M series. ...
  23. The old crusader I am looking at does not have a...

    The old crusader I am looking at does not have a floppy that I saw. just about a 40-50 page paperback instruction manual.
    Funny you said that about the older machines being simpler. The...
  24. I will be designing and building transmission...

    I will be designing and building transmission adapter plates for various small diesel engines to various domestic automatic and manual transmissions for Light trucks. Also turbocharger adapters, and...
  25. another question, with the Crusader series M...

    another question, with the Crusader series M control. Can you write a program away from the machine and then import it to the machine when you get to the shop??. I did see that the Lagun...
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4