Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Grnmtntri11

Search: Search took 0.00 seconds.

  1. Ha yeah i bet So it was most likely in a...

    Ha yeah i bet
    So it was most likely in a factory setting creating machines or tools you think?
    Wish I had Some background on it. Bought it from a guy who had it sitting out in the woods for years.
  2. HAHA If I have an ON/OFF switch on the front...

    HAHA

    If I have an ON/OFF switch on the front of the drill press already, can I keep the VFD toggle switch in the ON position and use the original on/off switch from drill press. Power to the...
  3. https://www.amazon.com/gp/aw/d/B01AOCJT0K?ref=ppx_...

    https://www.amazon.com/gp/aw/d/B01AOCJT0K?ref=ppx_pt2_mob_b_prod_image
  4. Yes it is. In the picture on the link itís in the...

    Yes it is. In the picture on the link itís in the back right
    Had the turn dial, on off toggle switch and optional forward and reverse toggle switch.
  5. Doesnt look like my last response posted. My...

    Doesnt look like my last response posted.

    My VFD is made by KB electronics, its the hybrid drive 1 to 3 phase. If my VFD has an on/off switch built in, I can go straight from the power supply...
  6. Iíve gotten, 85-90% off my hand sanding it. I...

    Iíve gotten, 85-90% off my hand sanding it. I might Do another round of muriatic acid at this point. But Iíll be moving that operation outside. Some ran down the legs onto my new concrete floor 🤦*♂️
  7. I tried That with no prevail. Used an oxy torch

    I tried That with no prevail. Used an oxy torch
  8. Heres a few pictures ABOVE^^ I am new to...

    Heres a few pictures ABOVE^^

    I am new to posting pics, some are before some are after, but I think youll get the general idea of the "PAINT" i am talking about.
    Also notice the stamped numbers I...
  9. 282904 282905 282906 282907

    282904
    282905
    282906
    282907
  10. 282902 282903

    282902
    282903
  11. So I trued Using my oxy torch and tested it In a...

    So I trued Using my oxy torch and tested it In a small 3x3 area. Tried heating it for minutes, tried scraping and nothing came off. Tried again with almost a cutting flame going, kept it on for...
  12. The ďpaintĒ on the surface isnít really acting...

    The ďpaintĒ on the surface isnít really acting like paint
    And it definitely is not millscale.
    Iíll try attaching the pictures if I Can Figure out how to successfully post them.
    My next step was...
  13. The ďpaintĒ is definitely not millscale. Iíll...

    The ďpaintĒ is definitely not millscale.
    Iíll attach some pictures of the progress Iíve made so you can see the surface. Itís very interesting stuff. I would Have thought paint would come off much...
  14. New welding table- painted top removal ideas

    Am I doing Something dangerous to my health by grinding this unknown substance off? Anyone know what it most likely could be?
    I bought A used steel topped table this week. 3x5í and 1.5Ē thick top. ...
  15. Thanks for the information Greg and others Iíll...

    Thanks for the information Greg and others
    Iíll most likely try and mount the vfd to my drill press and use it as the on/off switch and. It worry about a remote option.
  16. So there is no benefit to keeping the mag starter...

    So there is no benefit to keeping the mag starter in the equation?
  17. So, single phase power to the magnetic starter...

    So, single phase power to the magnetic starter (does this change how the wiring is laid out inside the starter?)
    Then single phase power leaving the starter to the VFD and then to the motor?

    I...
  18. Pics

    Shared album - Justin George - Google Photos
  19. 3ph POWERMATIC 1150 (How to wire vfd with mag starter)

    How do I wire In a vfd (havenít gotten it yet in the mail). I have single phase power in my shop.
    Itís a 3 phase drill press Motor with the furnas magnetic starter. where do i put the VFD? Do i...
  20. Replies
    102
    Views
    45,237

    Did you get any response about this? I need To...

    Did you get any response about this? I need To convert mine as well.
  21. Has anyone updated this elsewhere? I have A...

    Has anyone updated this elsewhere?
    I have A cp200 230v only machine and want to convert it... Iíve read all the forums in here and at Miller. Gooseman said it worked and then this says his didnít...
Results 1 to 21 of 21