Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rimcanyon

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    79
    Views
    18,948

    No, I didn't get it. [email protected]

    No, I didn't get it. [email protected]
  2. Replies
    46
    Views
    1,626

    Thanks for the replies. Here are some answers to...

    Thanks for the replies. Here are some answers to your questions:

    The 20A GFIC breakers flip when the start button on the RPC is pressed, and both can be reset when the RPC is running. The 20A...
  3. Replies
    46
    Views
    1,626

    The conduit to the RPC runs direct from the...

    The conduit to the RPC runs direct from the breaker panel and is not shared by any other circuit. The breaker panel is rated at 125A and the ampacity of #2 copper is also 120-130A. The 50A breaker...
  4. Replies
    46
    Views
    1,626

    The resistors were 15k not 1500k. Looking at...

    The resistors were 15k not 1500k. Looking at Fitch Williams' design, he only put the bleed resistors on the start caps. Maybe there is a reason? The ones that blew were on AC and BC legs. Here is...
  5. Replies
    46
    Views
    1,626

    RPC blows adjacent circuits

    New 15 HP RPC in a new shop with 100A service, everything new. This is attached to a subpanel fed from the original garage subpanel, with #2 copper wires run about 70'. I have two problems I would...
  6. Replies
    79
    Views
    18,948

    Email me...

    Email me...
  7. Don't waste $$ buying diodes from Monarch. You...

    Don't waste $$ buying diodes from Monarch. You can buy equivalents on Ebay for cheap, there are lots of threads about it. I have lots of extras if you need some.
  8. Replies
    19
    Views
    985

    Jim, have you seen this thread: Monarch 10EE...

    Jim, have you seen this thread: Monarch 10EE parts for Sale

    -Dave
  9. Yes, but you can install them with the lip down...

    Yes, but you can install them with the lip down if you swap them side for side. I've seen 10EE's both ways. Lip down doesn't collect chips. I think they came lip up from Monarch, but I have seen...
  10. Replies
    13
    Views
    936

    That two-piece cover was used on both mfg. and...

    That two-piece cover was used on both mfg. and toolroom lathes. It depends on whether the lathe was equipped with a collet closer other than a hand wheel. So it could have an air-operated closer or...
  11. Replies
    41
    Views
    7,398

    Nice work. Glad you got it back together again. ...

    Nice work. Glad you got it back together again. How is it working out?

    My Sundstrand throws the belt if the cut is too aggreussive, and I have configured the idler pulley with a bit of a tilt to...
  12. That suggestion has been around a long while. ...

    That suggestion has been around a long while. Then you are going to have to decide if the rounded corners go up or down. That debate has also been going on a long time.
  13. Replies
    79
    Views
    18,948

    Steve, please send email, I seldom see posts on...

    Steve, please send email, I seldom see posts on the forum in a timely fashion.

    Dave

    [email protected]
  14. The RPC should have suitable protection for its...

    The RPC should have suitable protection for its output circuits. If it is designed for a 30A load, then there should be a 30A circuit breaker on that output, but that is just to protect the wiring...
  15. Replies
    2
    Views
    418

    I have a complete lathe with one of those 5C D1-3...

    I have a complete lathe with one of those 5C D1-3 collet noses for less than the seller is asking for that adapter.
  16. Replies
    27
    Views
    1,683

    I've learned one thing that applies to brazing...

    I've learned one thing that applies to brazing Monarch cast parts: do not use flux-coated rod and expect it to do the job. I have had success using standard Victor general brazing borax flux,...
  17. Replies
    13
    Views
    936

    That is a standard toolroom lathe headstock cover...

    That is a standard toolroom lathe headstock cover for a lathe with lever-operated collet closer. The ring needs to be rotated 90 degrees so the hinge is on the back rather than the bottom. Your...
  18. Replies
    15
    Views
    1,431

    Bill, glad I could help. The Monarch forum has...

    Bill, glad I could help. The Monarch forum has always been a great place to get help, I have benefitted more times than I remember.
  19. Replies
    79
    Views
    18,948

    Don, email me, that is the only way you are going...

    Don, email me, that is the only way you are going to get a response. My email is [email protected], but you can also send me email using the forum. Thermite posted instructions a few replies back....
  20. Replies
    15
    Views
    1,431

    \ Excellent Glad you got it working. Dave

    \

    Excellent Glad you got it working.

    Dave
  21. Replies
    15
    Views
    1,431

    Here are a couple pictures that show the contact...

    Here are a couple pictures that show the contact and latch positions of the knob on mine:

    290178290179

    It appears to me that mine is contacting the plate closer to tdc. Try adding some shims...
  22. Replies
    79
    Views
    18,948

    What diameter? I have two spindle pulleys that...

    What diameter? I have two spindle pulleys that might work, one is 6 ½" the other is 7 ⅛". What is your gearbox pulley size and motor max rpm? The 6 ½" is brand new, still in the Monarch part bag.
  23. Replies
    15
    Views
    1,431

    OK, check a few things. I'm still guessing that...

    OK, check a few things. I'm still guessing that it is an alignment issue. When the top cover is in place but the latch is not engaged, the top should be located by three points: the bottom supports...
  24. Replies
    5
    Views
    538

    So never having seen a late model 10EE in the...

    So never having seen a late model 10EE in the flesh, this is a pure guess. I am thinking the round knob next to the apron hand wheel is like on any other 10EE: it moves in and out and selects feed...
  25. Replies
    5
    Views
    538

    I/M gearbox with only two levers ?????

    Monarch 10 EE Lathe , 10ee Lathe Dec 85 Precision Lathe | eBay

    Tell me what you think. Why are there only two levers on the left side of the I/M gearbox?
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4