Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: matt_isserstedt

Page 1 of 60 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    48
    Views
    5,757

    Imo, owner of the smallest MM-35 is that if you...

    Imo, owner of the smallest MM-35 is that if you get the sheared part up close to the pivot pin the shear blades are way out of parallel at the start of the cut for thick material. That leads to...
  2. Replies
    10
    Views
    592

    You'd do best to grind such material. Or grind...

    You'd do best to grind such material. Or grind thru the case with a dremel and then mill it.
  3. Replies
    28
    Views
    1,162

    Owner to Rigger: "I have this old lathe in my...

    Owner to Rigger: "I have this old lathe in my machine-cave that I want to remove so I can sell it, can you give me a bid?"

    Rigger to Owner (after seeing 4ft square hole): "$5k cash job we can...
  4. The rigging charge is what, north of $1k to do...

    The rigging charge is what, north of $1k to do this? $1k to get the crane to show up and then hourly after that? [don't know for sure but just WAG-ing]

    One can buy enough framing and roofing...
  5. Possible its valve guide, the exhaust valves...

    Possible its valve guide, the exhaust valves usually don't directly contribute but positive pressure can get pushed thru the oil side of the system and thru the PCV ventilation.

    Bottom line is if...
  6. Drill a pilot hole with a magnet drill? Or...

    Drill a pilot hole with a magnet drill?

    Or punch a clearance slug with a 60+ ton ironworker?
  7. I think Tennsmith could be used if oiling and...

    I think Tennsmith could be used if oiling and such was regularly attended to.

    Like light swab on the edges every couple of cycles, oil the eccentrics & pivot on the finger brake. Counteractive to...
  8. The move to 6" concrete is one I did for...

    The move to 6" concrete is one I did for forklifts. 6" of 3/4" washed limestone base, compacted, 10mil vapor barrier, 4ksi concrete mix, 1/2" rebar grid on 16" centers, curing sealer applied the...
  9. Replies
    7
    Views
    1,041

    Could also "lose" it which is going to get a new...

    Could also "lose" it which is going to get a new cc number. Tough to bill against a number which is inactive.

    Good that it worked out.
  10. Biggest pain in my shop configuration is dealing...

    Biggest pain in my shop configuration is dealing with 24ft long bars that come from the steel yard. (although I have no helpers).

    Its an extra set of detail, but getting the columns and footings...
  11. Replies
    9
    Views
    613

    Its nice to have an American Pattern double-cut...

    Its nice to have an American Pattern double-cut for quickly hogging off materials. Then a single cut American to finish off and get it smoother.

    A double-cut Swiss is a hybrid, its double-cut...
  12. Replies
    18
    Views
    1,813

    Man thats crazy! I hope they don't have to...

    Man thats crazy!

    I hope they don't have to stop for gas :D (yah, diesel)
  13. It was mindless boring work, went for 3 shifts, 7...

    It was mindless boring work, went for 3 shifts, 7 days.

    The "obstacles" were all manufactured, had the obtuse angle bermed rail crossing to induce max chassis-twist, some "potholes" made out of...
  14. That's a Motown Exit and has been going on here...

    That's a Motown Exit and has been going on here long before it got popular there. ;)

    It could be done, yes, but the trailer would be easier.

    I towed a GN trailer west of Chicago to pick up a...
  15. Great detail! One question, my eyeball says...

    Great detail!

    One question, my eyeball says the worms aren't the same pitch....but calibration of my glasses could be off :) and/or perspective or camera angle.
  16. What is up with all of those rods going thru the...

    What is up with all of those rods going thru the cross-slide? Is there power to the compound?

    Mine does not look like that!

    I ended up taking a gear out of the end train, was a lot of gear...
  17. Replies
    3
    Views
    682

    Hi Brian I have the pencil rubbings of plate...

    Hi Brian

    I have the pencil rubbings of plate and 2 versions of the forming nose, will send them to you, check PMs. Sorry for being absent minded in the first message!

    Plate is 1-3/16" thick x...
  18. Some pictures would help immensely. Also helpful...

    Some pictures would help immensely. Also helpful would be the amount of wear are we talking about? .010? More?

    Classic method is to turn shaft undersize to cleanup, bore hub oversize to cleanup...
  19. Replies
    41
    Views
    3,890

    A lot of stuff you have! I resemble that remark!...

    A lot of stuff you have! I resemble that remark! Have the XL extension cord to power anything needed. although there is now some more hard wiring.

    Although I like them I don't think I'll ever...
  20. Replies
    3
    Views
    682

    Well I took a picture of it. Sorry thats not...

    Well I took a picture of it. Sorry thats not what you asked for but I didn't have time at the time to disassemble it and rub. This one was previously abused and got rusty, now cleaned back up. It...
  21. Typical are solid steel bars... ...

    Typical are solid steel bars...

    https://www.practicalmachinist.com/vb/attachments/f85/231788d1530284900-help-fadal-3016-unloading-img_2199.jpg

    My VMC-15 has heavy box tubes that run the length...
  22. Does it use a neutral in the cord-set? I would...

    Does it use a neutral in the cord-set?

    I would expect 240vac/480vac on all combinations of phase-to-phase.

    Seems odd that it would be wired with a neutral, because then it couldn't be used on...
  23. This is off-topic but is that the -BCS Box Car...

    This is off-topic but is that the -BCS Box Car eSpecial? Looks like it has the high-stacked counterweight.

    The 4.3L has more width due to the "V" configuration. The old 250-6 (line 6) has tons...
  24. So I'm looking at a SendCutSend dot com brochure....

    So I'm looking at a SendCutSend dot com brochure. They have something ferrous (not sure if cold rolled, HRP&O or ?) that's .104 thick.

    Laser them out slightly oversize and grind to finish in...
  25. Replies
    162
    Views
    13,598

    I think I counted 3 posts in 4 pages about...

    I think I counted 3 posts in 4 pages about insulation....which works with both heat and A/C.

    One of the pesky things about heating air is that its slippery and likes to escape thru tiny gaps.

    I...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4