Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jancollc

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    117
    Views
    25,464

    Those are strange cutouts in the overhead guard....

    Those are strange cutouts in the overhead guard. Must be for lifting the battery with an overhead crane.

    I really liked the other one. The new one is probably nicer to use, but it's kind of like...
  2. Replies
    7
    Views
    411

    fanucs are weird about cards- there can be files...

    fanucs are weird about cards- there can be files on the card, but the control doesn't show them because they have the wrong extension.

    Have you plugged the card back into the laptop and checked...
  3. Replies
    24
    Views
    1,011

    That's a little confusing. Here's how I think...

    That's a little confusing. Here's how I think about it.

    There are two ways to program a toolpath. You can specify the center of spindle, or the edge of the part. Programming center of spindle, the...
  4. Replies
    38
    Views
    1,431

    Unless OP is doing a lot of sand blasting, a 15hp...

    Unless OP is doing a lot of sand blasting, a 15hp rotary seems like too much compressor for a garage shop. I'm running my shop on a 7.5hp and it makes more air than I need. A 15hp wouldn't even run...
  5. Shouldn't be hard to find a 3/4" shank ball mill....

    Shouldn't be hard to find a 3/4" shank ball mill.

    McMaster lists them.

    McMaster-Carr
  6. Replies
    16
    Views
    717

    What is the material that you have to run so slow?

    What is the material that you have to run so slow?
  7. Replies
    5
    Views
    495

    Even if your parts are so large that a used...

    Even if your parts are so large that a used tumbler was 6K, it would still pay for itself in short order compared to blasting them one at a time...

    You can find C&M 3FT^3 tumblers for a lot less...
  8. Replies
    308
    Views
    33,619

    The planners here have created an "Urban Growth...

    The planners here have created an "Urban Growth Boundary". Beyond which, the zoning prohibits most commercial activities. To prevent "urban sprawl" as they say. I think it's to keep the "farms and...
  9. Replies
    27
    Views
    1,539

    On my VMC's I always use IPM. On the lathe, it's...

    On my VMC's I always use IPM. On the lathe, it's IPR.

    Either one is fine, you just better know which one you are using...

    @OP- get your speeds and feeds better- for 250rpm you should feed at...
  10. Looks to me like the latter. With the exception...

    Looks to me like the latter. With the exception maybe of some 3D printing stuff.

    The list of exhibitors has no major MTB's that I can see. Lots of process stuff, not much in the way of machine...
  11. Replies
    14
    Views
    1,157

    Have you tried Crest? Marine Toe Rail &...

    Have you tried Crest?

    Marine Toe Rail & T-Track | Crest Aluminum Products Co, Inc
  12. Replies
    8
    Views
    795

    You can't just stuff a 10mm tap in an 8mm hole....

    You can't just stuff a 10mm tap in an 8mm hole. You have to drill first.

    You shouldn't do that anyway- you should helicoil it back to the original thread.
  13. Replies
    61
    Views
    7,551

    The certification they falsified was a process...

    The certification they falsified was a process (part of the heat treat} specification. It was not something that is going to show up in a lab test. The lab will tell you what you have, but it cannot...
  14. Replies
    14
    Views
    1,157

    What kind of profiles are you looking for? ...

    What kind of profiles are you looking for?

    Misumi stocks a bunch of standard profiles for doing frames and motion control type stuff.

    If you're looking for boat specific shapes like toerails...
  15. Replies
    6
    Views
    607

    Just practice. Bring your indicator down to just...

    Just practice. Bring your indicator down to just above the part, and sweep it around. Make your big adjustments. Then bring it down, do X first. Zero the dial on the first side, rotate 180 degrees...
  16. Replies
    8
    Views
    1,050

    If the leak is at the large bottle- either the...

    If the leak is at the large bottle- either the shutoff valve or the connection to the check valve, the small bottle would not see the pressure drop in the large bottle.
  17. Replies
    48
    Views
    25,288

    I assumed you had a floating holder by your...

    I assumed you had a floating holder by your feedrates. Yes, you can change the RPM in the program.

    The tension/extension holders vary. Some release, some don't. Releasing holders are designed that...
  18. Replies
    20
    Views
    1,445

    24 CFM will obviously be enough for a mini mill....

    24 CFM will obviously be enough for a mini mill.

    As to the rest- Dewalt, Porter Cable, Kobalt, Craftsman, etc are all cheap consumer grade compressors. Right at home in any garage.

    They will...
  19. ebay ad here: Faro 9ft EDGE Arm CMM w/ Laser...

    ebay ad here:

    Faro 9ft EDGE Arm CMM w/ Laser Scanner HD LLP 2015 V6 HARD CASE 3.9REV | eBay

    Seller does have 100% positive feedback on a large number of transactions, looks legit.
  20. Replies
    48
    Views
    25,288

    Well, you might start by putting F.050 in your...

    Well, you might start by putting F.050 in your G95 lines so your feedrate matches the tap's pitch.

    General practice to start the tapping cycle farther then .020" from the part, so your spindle has...
  21. Replies
    49
    Views
    2,207

    A new Gerstner would put any machinist "over the...

    A new Gerstner would put any machinist "over the moon". But one Gerstner would buy 5 Kennedy's, so there is that...

    We use our top boxes for measuring tools, which is why they have felt lined...
  22. CosmosK. I would be happy to be a CAT40...

    CosmosK. I would be happy to be a CAT40 volunteer. Also have BT40 and it would be great if it fits both.
  23. Replies
    11
    Views
    649

    My first look I thought is was an ONG keypad. I...

    My first look I thought is was an ONG keypad. I can make out the softkeys below the display.

    I zoomed the pic and see it's not a Fanuc ONG though, not sure what it is. Maybe an old Anilam or...
  24. Replies
    11
    Views
    649

    That's an old Fanuc 6M? I don't know what the...

    That's an old Fanuc 6M? I don't know what the other monitor is for.

    Assuming the control works, normal G code programming...

    edit: closer look, appears to have softkeys, so may be 10 or 11M.
    ...
  25. Replies
    5
    Views
    416

    I just hang them on a pegboard behind the machine.

    I just hang them on a pegboard behind the machine.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4