Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ferrretcatcher

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    132
    Views
    41,842

    This is my Clark IT60N forklift. Only rated for...

    This is my Clark IT60N forklift. Only rated for 6000lbs but it will do 7. Just rebuilt the 225 slant six 2 years ago. Forward reverse with a borg warner 4 speed so it will do 30 forward and...
  2. Replies
    3
    Views
    1,409

    I may have a wiring diagram for my machine if you...

    I may have a wiring diagram for my machine if you still need one. It will take me a bit to scan it.
  3. Replies
    14
    Views
    1,933

    I also have a Okuma LS 540x1500. I ordered a...

    I also have a Okuma LS 540x1500. I ordered a matched set for it about 15 years ago from Grainger. They were a truly matched set back then. Still going strong with those belts. I think it was...
  4. Dirty method would be to find a plate and tack it...

    Dirty method would be to find a plate and tack it at 3,6,9, and 12 so the barrel won't distort. Weld fitting on, then cut off plate. If you're welding on a fitting I would assume repaint of the...
  5. Replies
    26
    Views
    1,711

    I would think a strap wrench wrapped a few times...

    I would think a strap wrench wrapped a few times would get it tight enough not to leak with teflon tape. I have a few times used a properly sized split collar to grab the pipe just good enough not...
  6. The ones I was around were rosler metal...

    The ones I was around were rosler metal finishters and wheelabrator tunnel blast and tumblast tumble blasters. I think the tumblast used 3mm shot and the tunnel blast used 2mm shot. The shot was...
  7. My well at the previous place was a 6" pvc cased...

    My well at the previous place was a 6" pvc cased well with a 1" pvc pipe in it for water. They were threaded pvc ends and both the 6" and 1" were sch 160 pvc. Well was a franklin 3 phase pump. ...
  8. If you're not in a hurry I would ask if you could...

    If you're not in a hurry I would ask if you could get some concrete when they go by your place on another job. Might even be able to get leftovers from somebody else's jobsite. Otherwise I would...
  9. Replies
    47
    Views
    4,296

    Ill second the 6 flute MA Ford ones. I have some...

    Ill second the 6 flute MA Ford ones. I have some single flute and some 6 flute. If I'm just chamfering a hole ill use the single flutes. If I'm countersinking a flat head allen screw I will go for...
  10. DKMC, Did you change the whole distributor, shaft...

    DKMC, Did you change the whole distributor, shaft and all? How did you find one that fit? I ended up getting a newer dodge distributor with the reluctor element and did the HEI external module...
  11. It does ok. Yes the starter is different. If...

    It does ok. Yes the starter is different. If the op has the same forklift I have a part number. I think mine crossed to a challenger or something like that. Last year I pulled the engine on it...
  12. Do you still have these inserts? I am interested...

    Do you still have these inserts? I am interested in purchasing them if you do. Recently bought a cutter that takes them.
  13. Replies
    17
    Views
    1,080

    I might have a drawing somewhere for it but it...

    I might have a drawing somewhere for it but it will take a while to look. If you really needed 2 speed and its a ball bearing motor it might be worth messing with. If its a sleeve bearing motor I...
  14. I have a 225 slant six in my IT60N clark off road...

    I have a 225 slant six in my IT60N clark off road forklift. If you would post the model and serial number of your lift you would get better responses. I have replaced the starter on my forklift...
  15. I don't believe you can with a 1 degree machine. ...

    I don't believe you can with a 1 degree machine. The solenoid engages the curvic is the way I understand it. I don't believe there's a brake on the b, I think its just the drive holding position...
  16. I used to work at Deere and live in Cedar falls...

    I used to work at Deere and live in Cedar falls but I didn't know about this shop at all. There used to be a shop that did Bridgeport rebuilding, flame cutting, and Blanchard grinding in Waterloo...
  17. Parting off things can reduce some peoples QOL. ...

    Parting off things can reduce some peoples QOL. A guy I work with was parting off a smallish 1" by .75" nub off of a shaft. He got to the center of it and it came loose at around 500 rpm. This was...
  18. Reverse vise for VMC? Do you people use them?

    I'm working on some small projects on my new to me Mori MV55 and I am working with offsets like normal. I have more than a few setups and will have to change my coordinates for varying stock sizes. ...
  19. Replies
    4
    Views
    476

    It was not fun at all. You need to remove the...

    It was not fun at all. You need to remove the for/rev shaft I think but don't remember for sure. There's a tapered pin in both lead and feed screws that need to be driven out, pull the end bearing...
  20. Replies
    4
    Views
    476

    I have an Okuma LS 540x1500 10hp too. Okuma parts...

    I have an Okuma LS 540x1500 10hp too. Okuma parts are still available from Okuma but were expensive as I recall. Like STUPID expensive. My carriage was really dirty and a little rusty from running...
  21. Mine turned out great, The delivery company...

    Mine turned out great, The delivery company delivered it in the rain and was all worried about it not working when I got it. I opened it up even before I plugged it in and cleaned it out and tuned...
  22. I bought a bare bones one from HGR about 2 years...

    I bought a bare bones one from HGR about 2 years ago. They had about a dozen of them from somewhere so I thought I would take a chance one one of them. I bought one for $550 + $135 shipping. It...
  23. Another update, Got it all back together and it...

    Another update, Got it all back together and it was a real pain. The tool clamp pressure intensifier was awful! I got everything back together and couldn't get the drawbar to activate. Low...
  24. Metacut utilities or something similar?

    Hello all, I used to use a program called Metacut or Metacut utilities by Northwood designs. Haven't used the program for about 6 months but its darn handy for doing one offs and g code editing. ...
  25. I used to work on Inductoheat induction heaters...

    I used to work on Inductoheat induction heaters about 5 years ago. The capacitors will have bleed off resistors but the sign on the side said wait 10 minutes before opening the cabinet door. The...
Results 1 to 25 of 57
Page 1 of 3 1 2 3