Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: memphisjed

Page 1 of 33 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    37
    Views
    2,130

    Where to start-- Carbide blades have a place. ...

    Where to start--

    Carbide blades have a place. I run saws that can handle them, I run quantity that could benefit from them - and then there is a whole shift a workers after me... Carbides are not...
  2. Replies
    37
    Views
    3,030

    I think warm color bulbs look better in lanterns,...

    I think warm color bulbs look better in lanterns, the cool spectrum makes the eyes try and focus to much. Most bulbs have now a days have edison threads.
  3. That has to be gross after material - not sales. ...

    That has to be gross after material - not sales. Fabrication runs low margin but not that low. I think division 9 (they are amazons builder) is the largest now- a Canadian company with a tiger king...
  4. Replies
    37
    Views
    2,130

    That saw carbide would be waste of money and be...

    That saw carbide would be waste of money and be harder to cut with.

    Variable tooth with minimal of three teeth is old rule that works ok for uncontrolled feed- which is manual saws, gravity...
  5. Replies
    28
    Views
    3,165

    And the second is 12 dollar shipping. One is...

    And the second is 12 dollar shipping. One is from kennametal- they are going to fed ex it like you are a shop that needs the cutter right now- or yesterday.
    ...
  6. Replies
    3
    Views
    715

    Bobcad usually has a their fire sale pricing on...

    Bobcad usually has a their fire sale pricing on black friday.
  7. Replies
    29
    Views
    2,611

    I would use the shell command in cad.

    I would use the shell command in cad.
  8. I try to find creative methods like loosing the...

    I try to find creative methods like loosing the whole saw whenever the boss men decide its a good idea to use it. It cuts, blades last zero to less than par- the bad is it slings stupid hot stingy...
  9. This is typical of every field. Sounds a tad...

    This is typical of every field.
    Sounds a tad to much like you want to poach the ripe apples from someone's basket right now. If that is the case then either you will not get job do to supplier...
  10. allied makes ta inserts just for structural...

    allied makes ta inserts just for structural shapes. Gen 2 is significantly cheaper than gen 3- and your hole count does not warrant the the gen 3. These run slower than other inserts, but can take...
  11. Replies
    88
    Views
    9,432

    How I would do it if I had laser welder, Swiss,...

    How I would do it if I had laser welder, Swiss, and edm wire... very different.

    Edm a goose neck thread pointer.

    Put stock in fancy paints lathe:
    Relieve the backside (near where threads will...
  12. Replies
    88
    Views
    9,432

    If I was back in my old artsy repair world days-...

    If I was back in my old artsy repair world days- I would turn the axle on a tiny lathe using a wedge engraving tool - like a wood lathe freehand, only with optivisor and better background music. I...
  13. Replies
    41
    Views
    4,845

    If the suits are really looking at production...

    If the suits are really looking at production then they have to be throwing down serious cash for automation. Getting in the race to the bottom has high entry fees.
    Unless you are in Davidson you...
  14. Replies
    12
    Views
    1,174

    Thank you one and all. The naichi bit looks to...

    Thank you one and all.
    The naichi bit looks to be worth a test. If not then going to have the two step holes drill then mill. Not concerned about bur- tiny hole, tiny bur, and I have lots of...
  15. Replies
    12
    Views
    1,174

    interrupted cut hole drilling

    I might have a job coming with lots of holes (.1" diameter). The center of the hole is 1/32" from the edge of material. Will a stub length carbide drill chip itself up a lot and/or stay relatively...
  16. Replies
    23
    Views
    1,808

    dougs answer for tig works,silicon bronze mig...

    dougs answer for tig works,silicon bronze mig wire is pricey but also available. copper, maganese, silicon alloy. If you are darkening the bell you might be able to use phos-copper- that goo fills...
  17. Replies
    21
    Views
    1,698

    Best solution yet. If angle is just a debur (non...

    Best solution yet. If angle is just a debur (non critical) you can get standard #4 center drills from any supplier- cheap and they work.
  18. Put pin in the spindle and have cutter mounted on...

    Put pin in the spindle and have cutter mounted on table. No rotary needed.
  19. Replies
    21
    Views
    1,698

    #4 center drill and modify the countersink angle?

    #4 center drill and modify the countersink angle?
  20. Replies
    7
    Views
    664

    Start with 85 sfm at 2+ ipm and work backwards...

    Start with 85 sfm at 2+ ipm and work backwards and left from there.
    Running 100-120 sfm is likely closer, just start slower to grasp how hard to push thru the chrome entry cut. HSS blade, carbide...
  21. [url=https://www.digikey.com/en/products/detail/al...

    [url=https://www.digikey.com/en/products/detail/allegro-microsystems/ATS675LSETN-LT-T/4040906]

    credit to pico-systems. Reads the teeth of gears.
  22. Replies
    7
    Views
    664

    Cold saw or dry cut carbide saw? Cold saw should...

    Cold saw or dry cut carbide saw? Cold saw should last a lot longer- those dry cuts sounds plausible.
    Cold saw start gentle (no slamming material) and then keep a heavty pressure on it. They like...
  23. Replies
    21
    Views
    2,218

    Use the mill to make a punch/stamp.

    Use the mill to make a punch/stamp.
  24. mister. The speed of air clears chips and part. ...

    mister.
    The speed of air clears chips and part. You can turn off the liquid portion and just run air when you want. A flood coolant with enough pressure to do anything would be a giant mess in a...
  25. Replies
    8
    Views
    881

    a thick stainless bowl tacked to top. fire pots...

    a thick stainless bowl tacked to top. fire pots are consumables- granted slow but still consumables.
Results 1 to 25 of 813
Page 1 of 33 1 2 3 4