Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: coyoinu

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    624

    that's the classic control with a fancy skin. ...

    that's the classic control with a fancy skin. probably a 68k processor on the main board.
  2. rtfm - Parameter 315 bit 26, Status Relays,...

    rtfm -

    Parameter 315 bit 26, Status Relays, must be enabled.
  3. Replies
    3
    Views
    500

    sure, any text editor will do, but be careful,...

    sure, any text editor will do, but be careful, you may anger some elder gods.
  4. the next page past the Q code section in the...

    the next page past the Q code section in the Coldfire manual says something similar about the optional M code relay board

    • Spare Output Relay 45 Feed Rate Override is active (Feed Rate is NOT...
  5. Replies
    3
    Views
    500

    I think that file ends up in your User Data...

    I think that file ends up in your User Data folder in the List Program menu. Select it, F2, copy to USB.
  6. If you're working on a NGC control, you can watch...

    If you're working on a NGC control, you can watch the value in macro #62590 for feed override, #62591 for rapid override, and #62540 for main spindle, #62541 for sub, #62542 for live tool
  7. Replies
    17
    Views
    3,432

    with the bore being ~1.5", there's no way the...

    with the bore being ~1.5", there's no way the machine is ever reaching 200 IPM

    there's always servo error between the commanded position vs. actual position; the larger the feed rate, the larger...
  8. Replies
    12
    Views
    1,057

    if X+ is coming toward you, and Z+ goes to the...

    if X+ is coming toward you, and Z+ goes to the right, Y+ points straight down, according to the right hand rule.

    if you're doing any work in G19 plane, that one has G2 and G3 reversified from the...
  9. Replies
    46
    Views
    5,184

    So the machine does powerup fine with B working...

    So the machine does powerup fine with B working as expected, but borks out while running the program? Does B respond to hand jogging?

    Ya, sounds to me like a brake problem. It could be as...
  10. Replies
    2
    Views
    1,084

    if you're circle interpolating bores on a Haas,...

    if you're circle interpolating bores on a Haas, you need to be around 40 IPM or less to get "round" holes.
  11. Replies
    6
    Views
    1,060

    Adding to this, selecting the appropriate tip...

    Adding to this, selecting the appropriate tip direction will also be important to creating the feature correctly
  12. straight from the factory the tables can be out...

    straight from the factory the tables can be out of flat by .0015

    if you're using a tenths indicator, simply leaning on the sheet metal too hard is enough to distort the reading.
  13. Replies
    4
    Views
    1,503

    Coldfire alarm text says "Electronics fault. No...

    Coldfire alarm text says "Electronics fault. No communication between processor and Mocon. Power failure can be verified if Status LED on Mocon blinks four times at power up. Test +12 / -12 VDC to...
  14. Replies
    11
    Views
    2,300

    i don't think the gauge pin will be adequate. ...

    i don't think the gauge pin will be adequate. how do you know the length of the assembly? did you check the runout?

    there should be a master calibration tool which will have a known gauge...
  15. yeah the MRZP calibration has to be dead nuts,...

    yeah the MRZP calibration has to be dead nuts, probe included.

    markp posted a long-hand method to make the calibration, albeit for a different machine type
    ...
  16. Replies
    11
    Views
    2,300

    it sounds like you're starting the routine with...

    it sounds like you're starting the routine with no tool length offset for the probe. I find best results are had with "COMPLETE PROBE CALIBRATION", using both the calibrated gauge tool and the...
  17. remote share like netshare? Networking -...

    remote share like netshare?

    Networking - Troubleshooting Guide - NGC

    i've found that a netshare folder w/ more than 500 files in it causes problems with display and refresh speed.
  18. Replies
    18
    Views
    3,848

    maybe you can fill it with silicon bronze...

    maybe you can fill it with silicon bronze brazing, machine it back down, and finish flat.
  19. Replies
    2
    Views
    426

    well, the newest machines keep the door locked...

    well, the newest machines keep the door locked until the spindle is under 100 rpm, but there's a couple of things that the control simply can't protect you from (like if the encoder takes a hike)
    ...
  20. Replies
    2
    Views
    1,827

    post your code

    post your code
  21. Replies
    2
    Views
    387

    Settings -> User Positions -> Tailstock

    Settings -> User Positions -> Tailstock
  22. ^hey M, nice super mini mill 2 you got there

    ^hey M, nice super mini mill 2 you got there
  23. if grease-type lube, make sure that all lines are...

    if grease-type lube, make sure that all lines are functioning and flowing (rather than full of wax)
    good backup of parameters?
  24. Replies
    6
    Views
    1,422

    is this a UMC? if so, try this test again,...

    is this a UMC?

    if so, try this test again, and open the door gently but with enough force to bump the stops. watch the indicator while you do that.
  25. Thread: Haas simulator

    by coyoinu
    Replies
    5
    Views
    882

    offsets, bro

    offsets, bro
Results 1 to 25 of 206
Page 1 of 9 1 2 3 4